AP502 TriQuint, AP502 Datasheet - Page 2

• Manufacturer Part Number: AP502
• Description: RF Amplifier 2110-2170MHz 30dB Gain
• Manufacturer: TriQuint
• Type: Power Amplifierr

Specifications of AP502

• Operating Frequency: 2110 MHz to 2170 MHz
• Operating Supply Voltage: 12 V
• Supply Current: 840 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Number Of Channels: 1 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: [phone] • e-mail: [e-mail] • Web site: www.wj.com, www.TriQuint.com
The AP502-PCB and AP502 module is configured for Class AB by default. The resistor – R7 – which sets the current draw for
the amplifier is set at 0 Ω in this configuration. Increasing that value will decrease the quiescent and operating current of the
amplifier module, as described on the next page.
RF IN
33
32
31
30
29
28
-40
-45
-50
-55
-60
2110
18
3GPP W-CDMA, 1FA, Test Model 1+32 DPCH, ±5 MHz offset
-40 C
+25 C
+85 C
AP502
UMTS-band 4W HBT Amplifier Module
DNP
Narrowband S-Parameters
20
Performance Graphs – Class AB Configuration (AP502-PCB)
2130
Output Channel Power (dBm)
Frequency (MHz)
ACLR vs. Channel Power
+25 °C, Icq=850mA
0Ω
DNP
DNP
2140 MHz, Icq=850mA
S21
22
DNP
2150
0Ω
S11
24
S22
26
2170
DNP
6
100pF
.01μF
5
0
-5
-10
-15
-20
5
28
4
3
-20
-40
40
20
-40
-50
-60
-70
-80
0Ω
2
0
0
20
DNP
DNP
1
IMD3, IMD5, OIP3 vs. Ouptut Power
S21
S11
S22
500
22
Output Power per tone (dBm)
2140 MHz, +25 °C, Icq = 850mA
Wideband S-Parameters
10μF
1000
24
Frequency (MHz)
+25 °C, Icq=850mA
DNP
26
1500
100pF
.01μF
0Ω
28
2000
30
IMD3L
IMD3U
IMD5
OIP3
DNP
RF OUT
2500
32
60
50
40
30
20
3000
Notes:
1. Please note that for reliable operation, the evaluation board will have to
2. The area around the module underneath the PCB should not contain any
3. For proper and safe operation in the laboratory, the power-on sequencing
Specifications and information are subject to change without notice
be mounted to a much larger heat sink during operation and in laboratory
environments to dissipate the power consumed by the device. The use of
a convection fan is also recommended in laboratory environments.
Details of the mounting holes used in the WJ heatsink are given on the
last page of this datasheet.
soldermask in order to maintain good RF grounding.
should be followed:
a. Connect RF In and Out
b. Connect the voltages and ground pins as shown in the circuit.
c. Apply the RF signal
d. Power down with the reverse sequence
1000
38
36
34
32
30
28
950
900
850
800
750
-6
22
Gain / Output Power vs. Input Power
-4
24
Icc
PAE / Icc vs. Output Power
2140 MHz, +25 °C, Icq = 850mA
2140 MHz, +25 °C, Icq = 850mA
Input Power (dBm)
Output Power (dBm)
Product Information
-2
26
PAE
0
28
2
30
Page 2 of 5 July 2008
4
Pout
Gain
32
6
34
32.5
32
31.5
31
30.5
30
25
20
15
10
5
0