CWR11HH475KB Kemet, CWR11HH475KB Datasheet - Page 4

• Manufacturer Part Number: CWR11HH475KB
• Description: CAP TANT 4.7UF 15V 10% 1411
• Manufacturer: Kemet
• Series: Military, MIL-PRF-55365/8, CWR11r
• Type: Moldedr

Specifications of CWR11HH475KB

• Tolerance (+ Or -): 10%
• Voltage: 15VDC
• Esr: 4Ohm
• Mounting Style: Surface Mount
• Polarity: Polar
• Construction: SMT Chip
• Case Style: Molded
• Case Code: B
• Lead Spacing (nom): Not Requiredmm
• Df: 6%
• Dcl: 0.7uA
• Seal: Not Required
• Insulation: Not Required
• Failure Rate: B
• Wire Form: Not Required
• Product Length (mm): 3.5mm
• Product Height (mm): 1.9mm
• Product Depth (mm): 2.8mm
• Product Diameter (mm): Not Requiredmm
• Seated Plane Height: Not Requiredmm
• Length W/weld (max): Not Requiredmm
• Operating Temp Range: -55C to 125C
• Capacitance: 4.7uF
• Package / Case: 3528-21
• Voltage - Rated: 15V
• Tolerance: ±10%
• Esr (equivalent Series Resistance): 4.000 Ohm
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Size / Dimension: 0.138" L x 0.110" W (3.50mm x 2.80mm)
• Height - Seated (max): 0.083" (2.10mm)
• Lead Spacing: -
• Manufacturer Size Code: B
• Features: High Reliability
• Lifetime @ Temp.: -
• Lead Free Status / RoHS Status: Not Compliant

94
1. B1 dimension is a reference dimension for tape feeder clearance only.
2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
3. Tape with components shall pass around radius “R” without damage (see sketch A). The minimum trailer length (Fig. 2) may require
4. The cavity defined by A
embossment location and hole location shall be applied independent of each other.
additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2)
trude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical
restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm
maximum in the pocket (not applicable to vertical clearance.)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier
tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape
shall be pulled at a velocity of 300 ±10 mm/minute.
reels (with C-7280). Note that 13” reels are preferred.
Refer to EIA-556.
12 mm
12 mm
8 mm
8 mm
and
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone]
Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes.
Double
+0.004, -0.0)
(4 mm)
(8 mm)
Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13")
Single
+0.10 -0.0
12 mm
(0.059
8 mm
1.5
0
, B
0
, and K
(0.173)
(0.323)
ALUMINUM CHIP CAPACITORS
4.4
8.2
(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)
1.0 Kg Minimum.
TANTALUM, CERAMIC AND
1.75 ±0.10
0
The total peel strength of the cover tape from the carrier tape shall be:
shall be configured to surround the part with sufficient clearance such that the chip does not pro-
0.1 Newton to 1.0 Newton (10g to 100g)
0.1 Newton to 1.3 Newton (10g to 130g)
(0.039) (0.138 ±0.002)
(0.059) (0.217 ±0.002)
1.0
1.5
Packaging Information
4.0 ±0.10
3.5 ±0.05
5.5 ±0.05
Figure 1
(0.157 ±0.004) (0.984)
(0.315 ±0.004) (1.181)
2.0 ±0.05
4.0 ±0.10
8.0 ±0.10
(Metric will govern)
(0.024)
0.600
25.0
30.0
(0.098)
(0.181) (0.472 ±0.012)
(0.004)
0.100
2.5
4.6
(.315 ±0.012)
12.0 ±0.30
8.0 ±0.30