8501 3M Interconnect Solutions, 8501 Datasheet - Page 2

• Manufacturer Part Number: 8501
• Manufacturer: 3M Interconnect Solutions

Specifications of 8501

• Lead Free Status / RoHS Status: Not Compliant

Static-safe field service procedure
(See schematic below)
1. Upon arrival at the service call site, unfold the static-
2. Remove the accessories from the kit pockets, and attach
3. Slip on the elastic 3M™ Adjustable Wrist Band 2204.
3
Electronics
6801 River Place Blvd.
Austin, TX 78726-9000
800/328-1368
www.3M.com/electronics
Important Notice
All statements, technical information, and recommendations All statements,
technical information, and recommendations related to 3M’s products
are based on information believed to be reliable, but the accuracy or
completeness is not guaranteed. Before using this product, you must
evaluate it and determine if it is suitable for your intended application. You
assume all risks and liability associated with such use. Any statements
related to the product which are not contained in 3M’s current publications,
or any contrary statements contained on your purchase order shall have no
force or effect unless expressly agreed upon, in writing, by an authorized
officer of 3M.
• 3M
dissipative kit on any convenient area adjacent to the
trouble location.
the ground cord assembly to the red work surface by
means of the large black snap in the middle of the
cord. Connect the shorter of the two coiled sections to a
reliable ground via the alligator clip, which fits over the
banana plug. (Water pipes, unpainted equipment frames,
electrical conduits, or building frame members usually
provide accessible and reliable grounding locations.)
charges. The conductivity of the material ensures that the
boards or components will be protected from the static
charge existing on the carpet, tile, or table top beneath the
mat.
Adjust the size to fit comfortably, yet still contact the
entire circumference of the wrist. Contact need not to be
tight, but extremely loose fit is not desirable.
to work surface and wrist band,
then attach alligator clip to any
reliable ground
• Static-Dissipative
Work Surface
TM
Once grounded, the work surface cannot hold static
Ground Cord 3051 snap
• 3M
Wrist Band 2204
TM
Adjustable
4. Snap the longer coiled section of the ground cord
5. It is now safe to remove and handle static-sensitive
6. If recalls persist and indicate the possibility of user-
Cleaning
Clean the portable work surface with 3M™ Cleaner for
Static Control Mats 8001. It may also be cleaned with
mild detergent and water. Most strong solvents are not
recommended. The wrist band can be cleaned by hand
washing or in a standard washing machine.
Electrical performance
Note: Measuring the resistance of the work surface
requires a high voltage megohmmeter like the one in the
3M™ Test Kit 701. Using a 5-pound, 2-1/2” diameter
electrode*, the resistance to ground should be greater than
10
than 10
path to ground (bypassing the one megohm resistor in the
ground cord) which should be traced and corrected. If
the resistance is greater than 10
ground connection is interrupted and must be repaired.
*As specified in NFPA 99.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a
period of one year from the time of purchase. 3M MAKES NO OTHER
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. If this product is defective within the warranty period stated
above, your exclusive remedy shall be, at 3M’s option, to replace or repair
the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special,
incidental or consequential loss or damage arising from this 3M
product, regardless of the legal theory asserted.
Minimum 10%
Post-consumer fiber
6
assembly to the stud on the wrist band. This connects
the wrist band to the same common ground as the work
surface.
components.
NOTE: After removing a faulty part, put it immediately
into a 3M static-shielding bag to prevent further static
damage during its return trip to the repair depot.
its protective bag or container and inserted into the
equipment frame.
caused static damage, permanent placement of other 3M
static control products may be required.
ohms and less than 10
The replacement board can be removed from
6
ohms, it indicates the existence of an alternate
9
ohms. If the resistance is less
9
Printed in USA.
© 3M 2005 98-0799-0225-4
ohms, it means that the