5646446-1 TE Connectivity, 5646446-1 Datasheet - Page 3
![Conn Hard Metric RCP 88 POS 2mm Press Fit RA Thru-Hole](/photos/24/84/248418/3829070_sml.jpg)
5646446-1
Manufacturer Part Number
5646446-1
Description
Conn Hard Metric RCP 88 POS 2mm Press Fit RA Thru-Hole
Manufacturer
TE Connectivity
Type
Hard Metricr
Series
Z-PACKr
Specifications of 5646446-1
Pitch
2 mm
Number Of Rows
8
Number Of Contacts
88
Termination Method
Press Fit
Mounting
Through Hole
Contact Plating
Gold Over Nickel
Connector Type
Hard Metric (HM)
Row Pitch
2mm
Pitch Spacing
2mm
No. Of Contacts
88
Gender
Receptacle
Contact Termination
Right Angle Press Fit
No. Of Rows
8
Rohs Compliant
Yes
Product Type
Female
Number Of Positions / Contacts
88
Mounting Style
Through Hole
Pcb Mounting Orientation
Right Angle
Board Mount
Free Board
Module Length (mm [in])
25.00 [0.984]
Crosstalk Version
Standard
Amp Standard Option Number
1
Shielded
No
Interface Type
2mm HM
Termination End Plating
Tin over Nickel
Number Of Positions
88
Grounding Contact
Without
Rows Loaded
A, B, E, F, D, C, G, H
Contact Configuration
ACTION PIN Post, Signal
Feedthrough Post Length (mm [in])
3.30 [0.130]
Compactpci
Yes
Contact Plating, Mating Area, Material
Gold (30)
Contact Base Material
Phosphor Bronze
Connector Style
Receptacle
Mating Alignment
With
Mating Alignment Type
Multi-Purpose Center
Housing Color
Gray
Housing Material
Polyester GF
Ul Flammability Rating
UL 94V-0
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Lead Free Status / Rohs Status
Details
Polarization force.
Mating force.
Unmating force.
Contact retention force.
Module retention force.
ACTION PIN contact retention
force.
Gage retention force.
Durability.
Thermal shock.
Humidity-temperature cycling.
Humidity, steady state.
Rev A
Test Description
100 Newtons (22.48 pounds)
minimum.
See Note.
.75 Newton (2.7 ounces) maximum
per contact.
See Note.
.15 Newton (.5 ounce) minimum per
contact.
See Note.
5 Newtons (1.1 pounds) minimum in
mating direction.
10 Newtons (2.2 pounds) minimum
in unmating direction.
See Note.
74 Newtons (16.62 pounds)
minimum.
See Note.
20 Newtons (4.49 pounds)
minimum.
See Note.
15 grams (.53 ounce) minimum.
See Note.
See Note.
See Note.
See Note.
See Note.
Figure 1 (continued)
ENVIRONMENTAL
Requirement
IEC 512-7-13e.
Attempt to mate samples oriented
180E out of phase at maximum rate
of 12.7mm (.5 inch) per minute.
IEC 512-7-13e.
Measure force necessary to mate
samples at maximum rate of
12.7mm (.5 inch) per minute.
IEC 512-7-13e.
Measure force necessary to unmate
samples at maximum rate of
12.7mm (.5 inch) per minute.
IEC 512-8-15a.
Subject 20% of contacts to axial
load in both directions at maximum
rate of 10 Newtons per second until
specified load is reached and hold
for 10 seconds.
IEC 512-5-8a.
Measure force required to separate
module from housing.
See Figure 6.
IEC 512-8-15a.
Measure force required to separate
ACTION PIN from the printed circuit
board.
IEC 512-8-16e, Method A.
Insert and remove a .381mm (.015
inch) gage 3 times. Then insert a
.355mm (.014 inch) gage and
measure force required to remove.
See Figure 7.
IEC 512-5-9a.
Mate and unmate samples for 250
cycles at maximum rate of 600
cycles per hour.
IEC 512-6-11d.
Subject mated samples to 5 cycles
between -55 and 125° C.
IEC 512-6-11c, 11j, and 11m.
Subject mated samples to 6, 24
hour cycles between 25 and 40° C at
95% RH with -55° C cold shock.
IEC 512-6-11c.
Subject mated samples to steady
state humidity of 93% and 40° C for
21 days.
Procedure
108-1622
3 of 10