Q4010L5 Littelfuse / Teccor Brand Thyristors, Q4010L5 Datasheet - Page 6
![TRIAC ISOLATE 10A 400V TO-220AB](/photos/5/33/53368/to-220ab_isolated_sml.jpg)
Q4010L5
Manufacturer Part Number
Q4010L5
Description
TRIAC ISOLATE 10A 400V TO-220AB
Manufacturer
Littelfuse / Teccor Brand Thyristors
Datasheet
1.Q4010R5.pdf
(9 pages)
Specifications of Q4010L5
Triac Type
Standard
Mounting Type
Through Hole
Configuration
Single
Current - Hold (ih) (max)
50mA
Voltage - Off State
400V
Current - Gate Trigger (igt) (max)
50mA
Current - Non Rep. Surge 50, 60hz (itsm)
100A, 120A
Current - On State (it (rms)) (max)
10A
Voltage - Gate Trigger (vgt) (max)
2.5V
Package / Case
TO-220-3 Isolated Tab
Current - On State (it (rms) (max)
10A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
Q4010L5
Manufacturer:
LITTELFUSE/力特
Quantity:
20 000
Qxx10xx & Qxx10xHx Series
Soldering Parameters
Reflow Condition
Pre Heat
Average ramp up rate (Liquidus Temp)
(T
T
Reflow
Peak Temperature (T
Time within 5°C of actual peak
Temperature (t
Ramp-down Rate
Time 25°C to peak Temperature (T
Do not exceed
Physical Specifications
Terminal Finish
Body Material
Terminal Material
Design Considerations
Careful selection of the correct device for the application’s
operating parameters and environment will go a long way
toward extending the operating life of the Thyristor. Good
design practice should limit the maximum continuous
current through the main terminals to 75% of the device
rating. Other ways to ensure long life for a power discrete
semiconductor are proper heat sinking and selection of
voltage ratings for worst case conditions. Overheating,
overvoltage (including dv/dt), and surge currents are
the main killers of semiconductors. Correct mounting,
soldering, and forming of the leads also help protect
against component damage.
S(max)
L
10 Amp Standard & Alternistor (High Communitation) Triacs
) to peak
to T
L
- Ramp-up Rate
- Temperature Min (T
- Temperature Max (T
- Time (min to max) (t
- Temperature (T
- Temperature (t
p
)
P
)
100% Matte Tin-plated
UL recognized epoxy meeting flammabilty
classification 94V-0.
Copper Alloy
L
L
)
) (Liquidus)
s(min)
s(max)
s
)
P
)
Teccor
)
)
Pb – Free assembly
150°C
200°C
60 – 180 secs
5°C/second max
5°C/second max
217°C
60 – 150 seconds
260
20 – 40 seconds
5°C/second max
8 minutes Max.
280°C
Revised: November 1, 2010 05:04 PM
+0/-5
®
brand Thyristors
°C
94
AC Blocking
Temperature Cycling
Temperature/
Humidity
High Temp Storage
Low-Temp Storage
Thermal Shock
Autoclave
Resistance to
Solder Heat
Solderability
Lead Bend
Environmental Specifications
T
T
S(max)
S(min)
25
T
T
Please refer to http://www.littelfuse.com for current information.
Test
P
L
time to peak temperature
Specifications are subject to change without notice.
t
MIL -STD-750, M-1040, Cond A Applied
Peak AC voltage @ 125°C for 1008 hours
MIL -STD-750, M-1051, 100 cycles; -40°C
to +150°C, 15-min dwell-time
EIA/JEDEC, JESD22-A101 1008 hours;
320V - DC: 85°C; 85% rel humidity
MIL -STD-750, M-1031,
1008 hours; 150°C
1008 hours; -40°C
MIL -STD-750, M-1056 10 cycles; 0°C
to 100°C; 5-min dwell time at each
temperature; 10 sec (max) transfer time
between temperature
EIA/JEDEC, JESD22-A102 168 hours
(121°C at 2 ATMs) and 100% R/H
MIL-STD-750 Method 2031
ANSI/J-STD-002, category 3 Test A
MIL -STD-750, M-2036 Cond E
S
Preheat
Preheat
Specifications and Conditions
Ramp-up
Ramp-up
©2010 Littelfuse, Inc
t
t
P
L
Ramp-down
Ramp-do
Time