HEDS-9141#A00 Avago Technologies US Inc., HEDS-9141#A00 Datasheet
![Encoders 3 Channel 500CPR](/photos/16/35/163584/hedl-9100aoo_wht_sml.jpg)
HEDS-9141#A00
Specifications of HEDS-9141#A00
Related parts for HEDS-9141#A00
HEDS-9141#A00 Summary of contents
Page 1
... SIDE A HEDx-9xx1 Option 26.67 (1.05) 15.2 (0.60) 0.63 (0.025) SQR. TYP. OPTION CODE 5.1 (0.20) DATE CODE HEDS-9X01 1.02 ± 0.10 (0.040 ± 0.004) ALIGNING RECESS 2.44/2.41 DIA 1.85 (0.073) (0.096/0.095) 2.16 (0.085) 8.64 (0.340) DEEP REF. 17.27 (0 ...
Page 2
... The HEDS-9040 is designed for use with a HEDX-614X code w heel which has an optical radius of 23.36 mm (0.920 inch). The HEDS-9140 is designed for use with a HEDx-5x4x code w heel which has an optical radius of 11 ...
Page 3
Block Diagram RESISTOR LENS LED CODE EMITTER WHEEL SECTION Output Waveforms C P φ PHOTO COMPARATORS DIODES − − − I SIGNAL PROCESSING CIRCUITRY DETECTOR SECTION ...
Page 4
... Output Current per Channel ......................................................-1 OUT Shaft Axial Play . ............................................................................±0.25 mm (±0.010 in.) Shaft Eccentricity Plus Radial Play . ......................................... 0.1 mm (0.004 in.) TIR Velocity . ............................................................................................................ 30,000 RPM Acceleration ..........................................................................................250,000 rad/sec Note: 1. Absolute maximums for HEDS-5140/6140 codewheels only. 4 neighboring transition in the output of channel B. There are 4 states per cycle, each nominally 90°e. State Width Error (∆S): The deviation, in electrical degrees, of each state width from its ideal value of 90°e. Phase (φ): The number of electrical degrees between the center of the high state of channel A and the center of the high state of channel B. This value is nominally 90°e for quadrature output. Phase Error (∆ ...
Page 5
... Supply Voltage Load Capacitance Count Frequency Shaft Perpendicularity Plus Axial Play Shaft Eccentricity Plus Radial Play Note: The module performance is guaranteed to 100 kHz but can operate at higher frequencies. For the HEDS-9040 #T00 for operation below 0°C and greater than 50 kHz the maximum Pulse Width and Logic State Width errors are 60°e. Encoding Characteristics HEDS-9040 (except #T00), HEDS-9140 (except #B00) Encoding Characteristics over Recommended Operating Range and Recommended Mounting Tolerances unless otherwise specified. Values are for the worst error over the full rotation of HEDS-5140 and HEDS-6140 codewheels. Parameter Cycle Error Pulse Width Error Logic State Width Error Phase Error Position Error Index Pulse Width CH. I rise after -25°C to +100°C CH CH. A fall -40° ...
Page 6
... Encoding Characteristics HEDS-9040 #T00 Encoding Characteristics over Recommended Operating Range and Recommended Mounting Tolerances unless otherwise specified. Values are for the worst error over the full rotation of HEDM-614X Option TXX codewheel. Parameter Cycle Error Pulse Width Error Logic State Width Error Phase Error Position Error Index Pulse Width CH. I rise after CH CH. A fall -40°C to +100°C CH. I fall after CH CH. B rise -40°C to +100°C Note: 1. Module mounted on tolerance circle of ±0.13 mm (±0.005 in.) radius referenced from module Side A aligning recess centers. 2.7 kΩ pull-up resistors used on all encoder module outputs. Encoding Characteristic ...
Page 7
... Figure 1. Pull-up Resistors on HEDS-9X40 Encoder Module Outputs. Figure 2. HEDS-9X40 Mounting Tolerance. 7 Mounting Considerations Figure 2 shows a mounting tolerance requirement for proper operation of the HEDS-9040 and HEDS-9140. The Aligning Recess Centers must be located within a toler- ance circle of 0 ...
Page 8
... Mounting with an Alignment Tool The HEDS-8905 and HEDS-8906 alignment tools are rec- ommended for mounting the modules with Side B as the mounting plane. The HEDS-8905 is used to mount the HEDS-9140, and the HEDS-8906 is used to mount the HEDS-9040. These tools fix the module position using the codewheel hub as a reference. They will not work if Side A is used as the mounting plane. The following assembly procedure uses the HEDS- ...
Page 9
... HEDS-9040 fig 6a 50.48 DIA. (1.987) MAX. SETSCREW INDEX PULSE 130° POSITION TYPICAL ARTWORK SIDE (HEDM-6141) Figure 6b. HEDM-614X Series Codewheel used with HEDS-9040 #T00. HEDS-9040 fig 6b #2-56 SETSCREW USE 0.035" HEX WRENCH CODEWHEEL BOSS 26.67 18.0 (1.050) 19.0 (0.747) (0.71) MAX. ...
Page 10
... Orientation of Artwork for HEDS-9040 Option T00 (2000 CPR, 23.36mm Rop) and HEDS-9140 Option B00 (1000CPR, 11.00mm Rop) The Index area on the HEDS- 9040 Option T00, 2000 CPR and HEDS-9140 Option B00, 1000 CPR Encoder Module has a nonsymmetrical pattern as does the mating Code- wheel. In order for the Index to operate, the “Rightread- ing” side of the Codewheel disk (the “Artwork Side”) must point toward “Side A” of the Module (the side with the connecting pins) ...
Page 11
... Connectors Manufacturer Part Number AMP 103686-4 640442-5 Avago HEDS-8902 (2 ch.) with 4-wire leads HEDS-8903 (3 ch.) with 5-wire leads Molex 2695 series with 2759 series term. Figure 8. HEDS-8903 Connector. Typical Interfaces HEDS–9040 OR HEDS-9140 HEDS–9040 OR HEDS-9140 11 CH. A HCTL-20xx CH. B QUADRATURE DECODER/COUNTER CH HCTL-1100 CH. B MOTION CONTROL IC CH. I HOST PROCESSOR HOST PROCESSOR ...
Page 12
... Three Channel Encoder Modules and Codewheels, 23.36 mm Optical Radius HEDS-9040 Option 0 0 Resolution (Cycles/Rev Artwork on hub side (use when module Side B is down 2000 CPR 1 - Artwork opposite hub side (use when Module Side A is down HEDS-9040 * HEDS-9041 * HEDS-6140 B J HEDM-6140 T 12 HEDS-6140 Option Resolution (Cycles/Rev 1/4 in 1000 CPR 08 - 3/8 in 1024 CPR 09 - 1/2 in 5/8 in. HEDM-614 Option Artwork Orientation ...
Page 13
... For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. Obsoletes 5988-5498EN AV02-1132EN - April 5, 2011 HEDS-5140 Option Resolution (Cycles/Rev CPR ...