PE-65950 PULSE ELECTRONICS CORPORATION, PE-65950 Datasheet
PE-65950
Specifications of PE-65950
Available stocks
Related parts for PE-65950
PE-65950 Summary of contents
Page 1
... ISDN S-INTERFACE TRANSFORMERS Surface Mount, Dual, 2000Vrms Electrical Specifications @ 25°C — Operating Temperature 0°C to 70° Ratio OCL Pri Part (±2%) (mH MIN) Number & B PE-65792 1:1 1:2 22 PE-65793 1:1 1:1 22 PE-65795 1:2 1:2 22 PE-65798 1:2.5 1:2.5 22 PE-65799 1:2 1:2 22 NOTE: For low profile version of products listed above, refer to data sheet T613. ...
Page 2
... ISDN S-INTERFACE TRANSFORMERS Through Hole, Single, 2000Vrms Electrical Specifications @ 25°C — Operating Temperature 0°C to 70°C 2KV SOLATION HROUGH OLE INGLE A Part Ratio OCL Pri Number (±2%) (mH MIN) (µH MAX) PE-64993 1CT:1CT 22 PE-64994 1CT:1.8CS 22 PE-64995 1CT:2CT 22 PE-64996 1CT:2.5CS 22 PE-64998 1CS:2.5CS 22 PE-64999 ...
Page 3
... Single PE-65492 1:1 PE-64993 PE-65493 1:1 PE-64993 PE-65495 1:2 PE-64995 PE-65498 1:2.5 PE-64998 PE-65499 1:2 PE-64999 NOTE: Refer to the equivalent single part number for electrical specifications. Mechanical ID-1 .920 MAX 23, .560 MAX 14,22 PE-6549X DATE CODE 1 8 .130 ± .020 3,30 ...
Page 4
... D. National recommends a 1:2 receive transformer, but used as a 1:1 ratio by connecting only half the secondary winding. See National’s application note. E. PE-65950, PE-68613 and PE-65853 are recommended for use with Siemens PEB 2080/2085 and help in meeting the required longitudinal balance. F. Standard packaging for all chokes and transformers listed in this catalog is anti-static tubes ...
Page 5
... Longitudinal Balance for Transformers – The longitudi- nal conversion loss specification in I.430 includes a test setup that is intended for system evaluation, whether TE or NT. Such a test is performed with DC current present. The transformer plays an essential role in achieving the required balance. However, all other elements in the circuit should be also designed to provide the highest possible symmetry ...
Page 6
... A recommended test setup is shown in Figure 2. A high inductance “low frequency” common mode choke, such as PE-65950 or PE-65853, is recommended to improve balance correct inherent unbalances of some circuits. 4. Impedance Requirements – The requirements for minimum impedance in the inactive and powered-down states are expressed by impedance templates for both transmitter and receiver in NT and TE ...
Page 7
... IN-1/C (Through Hole) 0.25 500 IN-1/C (Through Hole) 0.40 500 SH-4/C (Surface Mount) 0.30 500 LA-1/C (Surface Mount) 20K 18K 16K 14K 12K PE-65541 10K 8K PE-65950/65853 6K 4K PE-65542 2K 0 100 KHz 1 MHz Frequency 3.0K 2.8K 2.6K PE-65854 2.4K 2.2K 2.0K 1.8K 1.6K PE-65554/65857 1 ...
Page 8
... FAX: 44 1483 401701 FAX: 858 674 8262 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2006. Pulse Engineering, Inc. All rights reserved. ...