W2E143-AA15-01 EBM-Papst Industries Inc, W2E143-AA15-01 Datasheet - Page 6

• Manufacturer Part Number: W2E143-AA15-01
• Description: FAN EXHAUST 172 X 51MM 115VAC
• Manufacturer: EBM-Papst Industries Inc
• Series: W2E143r
• Type: Roundr

Specifications of W2E143-AA15-01

• Current Type: AC
• Supply Voltage: 115 V
• Bearing Type: Ball
• Termination Style: 60 dB(A)
• Fan Type: Tubeaxial
• Size / Dimension: Round - 172mm Dia x 51mm W
• Voltage Rating: 115VAC
• Power (watts): 26W
• Rpm: 3300 RPM
• Noise: 60 dB(A)
• Air Flow: 258.9 CFM (7.33m³/min)
• Termination: 2 Terminals
• Weight: 2.1 lbs (952.5g)
• Speed: 3300 RPM
• Frame Dimensions (mm): 172 mm x 55 mm
• Housing Material: Aluminum Die-Cast
• Power Rating: 26 W
• External Depth: 51mm
• External Diameter: 172mm
• Flow Rate: 260CFM
• Noise Rating: 58dBA
• Power Connection Type: Terminal
• Diameter: 172mm
• Brand/series: W2E143
• Dimensions: 6.75 x 2.01 "
• Direction: Exhaust over Struts
• Frequency: 60 Hz
• Noise Level: 60 dBA
• Power, Rating: 26 W
• Size: 6.75 x 2.01 (171.5 x 51.1) In. (mm)
• Temperature, Operating, Maximum: +70 °C
• Voltage, Rating: 115 VAC
• Flow Rate - Imperial: 260CFM
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Static Pressure: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 381-1065; W2E143AA1501

4. CONNECTION AND START-UP
4.1 Connecting the mechanical system
4.2 Connecting the electrical system
4.2.1 Prerequisites
Item no.: 11120-5-9970 · Revision status: KM67974 · Print-out on 03/12/2010 · Created by A. Kehm (VM---) · Page 6 of 9
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone: [phone] · Fax: [phone] · [e-mail] · www.ebmpapst.com
W2E143-AA15-01
Check the device for transport damage. Damaged devices must no
longer be installed.
Install the undamaged device according to your application.
Check whether the data on the type plate agree with the connection
data and the data of the operating capacitor.
Before connecting the device, ensure that the supply voltage matches
the operating voltage of the device.
Only use cables designed for current according to the type plate.
CAUTION
Cutting and crushing hazard when removing the fan
from the packaging
DANGER
Electric voltage on the device
Electric shock
DANGER
Incorrect insulation
Risk of fatal injury from electric shock
CAUTION
Electrical voltage
The fan is a built-in component and features no electrically
isolating switch.
NOTE
Water penetration into leads or wires
Water enters at the cable end on the customers side and can
damage the device.
Connect the device only to circuits that can be switched off
using an all-pole disconnecting switch.
Carefully lift the fan out of its packaging, only touching the
housing. Make sure to avoid any shock.
Wear safety shoes and cut-resistant safety gloves.
Always install a protective earth.
Check the protective earth.
Use only cables that meet the specified installation
requirements for voltage, current, insulation material, load etc.
Route cables such that they cannot touch any rotating
parts.
Only connect the fan to circuits that can be switched off with
an all-pole separating switch.
When working on the fan, you must switch off the
installation/machine in which the fan is installed and secure it
from being switched on again.
Make sure that the cable end is connected in a dry
environment.
Operating instructions
4.2.2 Voltage control
4.2.3 Frequency inverter
4.3 Connection via plug
4.3.1 Preparing connection lines for the connection
Connect the connection lines to the mating connectors.
With open loop speed control using transformers or electronic
voltage regulators (e.g. phase angle control), excessive current
may occur.
In addition, noises can occur with phase angle control
depending on the mounting situation.
Fit sinusoidal filters that work on all poles (live-live and live-
earth) between the frequency inverter and the motor for
operation with frequency inverters.
Depending on how the device is installed, noises may occur.
The lines, including customer-side interface, fall within the
standard of the internal connection.
Observe product conformity to standards and the type of
protection in your end device after you have installed the ebm-
papst device.