W2E142-BB05-87 EBM-Papst Industries Inc, W2E142-BB05-87 Datasheet - Page 6

• Manufacturer Part Number: W2E142-BB05-87
• Description: FAN TUBEAXIAL 172X38MM 115VAC
• Manufacturer: EBM-Papst Industries Inc
• Series: W2E142r

Specifications of W2E142-BB05-87

• Voltage Rating: 115VAC
• Power (watts): 24W
• Size / Dimension: Rectangular/Rounded- 172mm L x 150mm H x 38mm W
• Termination: 2 Terminals
• Fan Type: Tubeaxial
• Termination Style: 57 dB(A)
• Air Flow: 230.0 CFM (6.51m³/min)
• Bearing Type: Ball
• Weight: 1.8 lbs (816.47g)
• Rpm: 3350 RPM
• Noise: 57 dB(A)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Static Pressure: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: W2E142BB0587

4. CONNECTION AND START-UP
4.1 Connecting the mechanical system
4.2 Connecting the electrical system
4.2.1 Prerequisites
4.2.2 Voltage control
4.2.3 Frequency inverter
Item no.: 10914-5-9970 · Revision status: KM70969 · Print-out on 04/08/2010 · Created by A. Kehm (VM---) · Page 6 of 9
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · 74673 Mulfingen · Phone: [phone] · Fax: [phone] · www.ebmpapst.com · [e-mail]
W2E142-BB05-87
Install the device according to your application.
Check whether the data on the type plate agree with the connection
data and the data of the operating capacitor.
Before connecting the device, ensure that the supply voltage matches
the operating voltage of the device.
Only use cables designed for current according to the type plate.
CAUTION
Cutting and crushing hazard when removing the fan
from the packaging
CAUTION
Electrical voltage
The fan is a built-in component and features no electrically
isolating switch.
NOTE
Water penetration into leads or wires
Water enters at the cable end on the customers side and can
damage the device.
Connect the device only to circuits that can be switched off
using an all-pole disconnecting switch.
With open loop speed control using transformers or electronic
voltage regulators (e.g. phase angle control), excessive current
may occur.
In addition, noises can occur with phase angle control
depending on the mounting situation.
Fit sinusoidal filters that work on all poles (live-live and live-
earth) between the frequency inverter and the motor for
operation with frequency inverters.
Depending on how the device is installed, noises may occur.
Carefully lift the fan out of its packaging, only touching the
housing. Make sure to avoid any shock.
Wear safety shoes and cut-resistant safety gloves.
Only connect the fan to circuits that can be switched off with
an all-pole separating switch.
When working on the fan, you must switch off the
installation/machine in which the fan is installed and secure it
from being switched on again.
Make sure that the cable end is connected in a dry
environment.
Operating instructions
4.3 Connection via plug
4.3.1 Preparing connection lines for the connection
4.3.2 Establish supply connections
Connect the connection lines to the mating connectors.
Check the PIN assignment of your connector.
Connect the panel connector and mating connector.
Ensure that the connector is locked in correctly.
The lines, including customer-side interface, fall within the
standard of the internal connection.
Observe product conformity to standards and the type of
protection in your end device after you have installed the ebm-
papst device.