IDT5T9316NLI8 IDT, Integrated Device Technology Inc, IDT5T9316NLI8 Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT5T9316NLI8
Manufacturer Part Number
IDT5T9316NLI8
Description
Manufacturer
IDT, Integrated Device Technology Inc
Type
Clock Driverr
Datasheet
1.IDT5T9316NLI8.pdf
(13 pages)
Specifications of IDT5T9316NLI8
Number Of Clock Inputs
2
Mode Of Operation
Differential
Output Frequency
1000MHz
Output Logic Level
LVDS
Operating Supply Voltage (min)
2.3V
Operating Supply Voltage (typ)
2.5V
Operating Supply Voltage (max)
2.7V
Package Type
VFQFPN
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
52
Quiescent Current
350mA
Lead Free Status / RoHS Status
Not Compliant
RECOMMENDED OPERATING RANGE
ABSOLUTE MAXIMUM RATINGS
PIN DESCRIPTION
NOTES:
1. Inputs are capable of translating the following interface standards:
2. Because the gate controls are asynchronous, runt pulses are possible. It is the user's responsibility to either time the gate control signals to minimize the possibility of runt
3. It is recommended that the outputs be disabled before entering power-down mode. It is also recommended that the outputs remain disabled until the device completes power-
4. The user must take precautions with any differential input interface standard being used in order to prevent instability when there is no input signal.
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
2. Not to exceed 3.6V.
Symbol
IDT5T9316
2.5V LVDS 1:16 CLOCK BUFFER TERABUFFER II
Symbol
V
V
V
T
T
GND
STG
J
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
Single-ended 3.3V and 2.5V LVTTL levels
Differential HSTL and eHSTL levels
Differential LVEPECL (2.5V) and LVPECL (3.3V) levels
Differential LVDS levels
Differential CML levels
pulses or be able to tolerate them in down stream circuitry.
up after asserting PD.
DD
A
A
I
O
SEL
V
N C
PD
G
G
GL
Qn
Qn
Symbol
[1:2]
[1:2]
DD
1
2
V
T
DD
A
Power Supply Voltage
Input Voltage
Output Voltage
Storage Temperature
Junction Temperature
I/O
O
O
I
I
I
I
I
I
I
Description
Ambient Operating Temperature
Internal Power Supply Voltage
Adjustable
Adjustable
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVDS
LVDS
Description
Type
PWR
PWR
(2)
(1,4)
(1,4)
Description
Clock input. A
Complementary clock inputs. A
desired toggle voltage for A
Gate control for differential outputs Q
HIGH, the differential outputs are asynchronously driven to the level designated by GL
Gate control for differential outputs Q
HIGH, the differential outputs are asynchronously driven to the level designated by GL
Specifies output disable level. If HIGH, "true" outputs disable HIGH and "complementary" outputs disable LOW. If LOW, "true"
outputs disable LOW and "complementary" outputs disable HIGH.
Clock outputs
Complementary clock outputs
Reference clock select. When LOW, selects A
Power-down control. Shuts off entire chip. If LOW, the device goes into low power mode. Inputs and outputs are disabled. Both
"true" and "complementary" outputs will pull to V
Power supply for the device core and inputs
Power supply return for all power
No connect; recommended to connect to GND
[1:2]
–0.5 to V
is the "true" side of the differential clock input.
–0.5 to +3.6
–0.5 to +3.6
–65 to +150
Max
150
DD
[1:2]
+0.5
3.3V LVTTL V
2.5V LVTTL V
:
(1)
[1:2]
is the complementary side of A
1
9
Unit
and Q
and Q
°C
°C
V
V
V
REF
REF
3
1
9
through Q
through Q
2
= 1650mV
= 1250mV
CAPACITANCE
NOTE:
1. This parameter is measured at characterization but not tested
DD
and A
Symbol
C
. Set HIGH for normal operation.
IN
2
16
8
. When HIGH, selects A
and Q
and Q
Min.
–40
2.3
Input Capacitance
8
16
. When G
Parameter
[1:2].
. When G
For LVTTL single-ended operation, A
1
is LOW, the differential outputs are active. When G
2
is LOW, the differential outputs are active. When G
Typ.
+25
(1)
2.5
1
and A
(3)
INDUSTRIAL TEMPERATURE RANGE
(2)
(2)
(T
.
.
A
1
.
= +25°C, F = 1.0MHz)
Min
—
Max.
+85
2.7
Typ.
—
[1:2]
should be set to the
Max.
3
Unit
°C
V
Unit
pF
1
is
2
is