2-1761607-9 TE Connectivity, 2-1761607-9 Datasheet - Page 4

• Manufacturer Part Number: 2-1761607-9
• Description: Conn Ejector Header HDR 26 POS 2.54mm Solder RA Thru-Hole
• Manufacturer: TE Connectivity
• Type: Ejector Headerr
• Series: AMP-LATCHr

Specifications of 2-1761607-9

• Pitch: 2.54 mm
• Number Of Rows: 2
• Number Of Contacts: 26
• Gender: HDR
• Contact Plating: Gold Over Nickel
• Termination Method: Solder
• Rohs Compliant: YES
• Connector Type: Wire To Board
• Contact Termination: Through Hole Right Angle
• No. Of Contacts: 26
• No. Of Rows: 2
• Pitch Spacing: 2.54mm
• Product Line: AMP-LATCH
• Profile: Low
• Pcb Mounting Orientation: Right Angle
• Pcb Mount Retention: Without
• Mating Connector Lock: Without
• Housing Style: 4-Sided
• Ejection Latches: With
• Post Size (mm [in]): 0.64 [.025]
• Shrouded: Yes
• [shrouded] End Dimension (mm [in]): 3.81 [0.150]
• Termination Post Length (mm [in]): 2.60 [0.102]
• Solder Tail Contact Plating: Tin over Nickel
• Header Type: Pin Header
• Number Of Positions: 26
• Centerline, Matrix (mm [in]): 2.54 x 2.54 [.100 x .100]
• Daisy Chain: With
• Preloaded: Yes
• Contact Plating, Mating Area, Material: Gold Flash over Palladium Nickel
• Contact Shape: Square
• Contact Base Material: Phosphor Bronze
• Connector Style: Header - Pin
• Mating Alignment Type: Center, Military
• Mating Alignment: With
• Housing Material: Thermoplastic - GF
• Ul Flammability Rating: UL 94V-0
• Housing Color: Blue
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Temperature Rating: Standard

4.
4.1.
4.2.
4.3.
4.4.
Rev F
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form , fit or function are m ade to the product or m anufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determ ined by developm ent/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product m eets the requirem ents of Figure 1. Failures
attributed to equipm ent, test setup or operator deficiencies shall not disqualify the product. W hen
product failure occurs, corrective action shall be taken and specim ens resubm itted for qualification.
Testing to confirm corrective action is required before resubm ittal.
Quality Conform ance Inspection
The applicable quality inspection plan will specify sam pling acceptable quality level to be used.
Dim ensional and functional requirem ents shall be in accordance with the applicable product drawing
and this specification.
Specim en Selection
Specim ens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. All test groups shall each consist of a m inim um of 5
headers of each type.
Test Sequence
Qualification inspection shall be verified by testing specim ens as specified in Figure 2.
108-40018
4 of 5