SI2434-C-GT Silicon Laboratories Inc, SI2434-C-GT Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI2434-C-GT
Manufacturer Part Number
SI2434-C-GT
Description
Manufacturer
Silicon Laboratories Inc
Datasheet
1.SI2434-C-GT.pdf
(74 pages)
Specifications of SI2434-C-GT
Main Category
Chipset
Data Rate
32.8125Kbps
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Lead Free Status / RoHS Status
Supplier Unconfirmed
Xn
X0
X1
X2
X3
X4
X5
Yn
Y0
Y1
Z
:E
:I
:M
:P
:R
:U
Command
Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued)
Call Progress Monitor (CPM)—This command controls which CPM signals are monitored
and reported to the host from the Si2457/34/15/04. (See Table 14 on page 36.)
Basic results; disable CPM—Blind dial (does not wait for dial tone). CONNECT message
does not include speed.
Extended results; disable CPM—Blind dial. CONNECT message includes speed.
Extended results and detect dial tone only—Add dial tone detection to X1 mode. Does not
blind dial.
Extended results and detect busy only—Add busy tone detection to X1 mode.
Extended results, full CPM—Full CPM enabled, CONNECT message includes speed.
Extended results—Full CPM enabled including ringback detection. Adds ringback detection
to X4 mode.
Long space disconnect—Modem hangs up after 1.5 seconds or more of continuous space
while on-line.
Disable.
Enable.
Hard Reset—This command is functionally equivalent to pulsing the RESET pin low. (See
t
Read from serial EEPROM.
Interrupt Read—This command causes the ISOmodem® to report the lower 8 bits of the
interrupt register I/O Control 0 (U70). The CID, OCD, PPD, and RI bits also are cleared, and
the INT pin (INT bit in parallel mode) is deactivated on this read.
Write to serial EEPROM.
Program RAM Write—This command is used to upload firmware supplied by Silicon Labs to
the Si2457/34/15/04. The format for this command is AT:Paaaa,xxxx,yyyy,.... where aaaa is
the first address in hexadecimal and xxxx,yyyy,.... is data in hexadecimal. Only one :P com-
mand is allowed per AT command line. No other commands can be concatenated in the :P
command line. This command is only for use with special files provided by Silicon Laborato-
ries. Do not attempt to use this command for any other purpose.
User-Access Register Read—This command allows the user to read from the user-access
registers. (See pages page 42–page 60.) The format is “AT:Raa”, where
aa = user-access address in hexadecimal.
The “AT:R” command causes all the U- registers to be displayed.
User-Access Register Write—This command allows the user to write to the 16-bit user-
access registers. (See page page 42.) The format is “AT:Uaa,xxxx,yyyy,zzzz,...” where
aa = user-access address in hexadecimal.
xxxx = Data in hexadecimal to be written to location aa.
yyyy = Data in hexadecimal to be written to location (aa + 1).
zzzz = Data in hexadecimal to be written to location (aa + 2).
etc.
AT
in Table 6 on page 7.)
Rev. 1.1
Action
Si2457/34/15/04
23