XE0017 Cermetek Microelectronics, XE0017 Datasheet

no-image

XE0017

Manufacturer Part Number
XE0017
Description
Manufacturer
Cermetek Microelectronics
Datasheet

Specifications of XE0017

Lead Free Status / RoHS Status
Supplier Unconfirmed
Description
The XE0017 is fully-integrated, low-profile, high-
performance telephone line interface module. It
complies with FCC Part 68 requirements for direct
connection to the public switched telephone network.
The XE0017 meets the technical requirements for data
transmission at rates up to 33,600 bps. It is also suitable
for fax and voice communications. The XE0017 was
specifically designed to be compatible with Rockwell
Socket Modems.
The XE0017 is a complete DAA. It includes a low
distortion telephone line transformer, ring detector,
hookswitch and 2-4 wire convertor. The 2-4 wire
convertor separates transmit and receive signals. The
XE0017 operates from a single +5 volt supply and fits in
a 0.260 inch high package.
XECOM
Low-Profile, V.34 Compatible Telephone Line Interface
RI
OH
Tx
Rx
CONVERTER
2 TO 4
WIRE
XE0017 Block Diagram
PROTECTIVE
NETWORK
SURGE
AND
(1)
Features
*
*
*
*
*
*
*
*
*
*
Small Size:
0.95 inches by 0.925 inches by 0.260 inches
FCC Part 68 Compliant
V.34 compatible
Compatible with Rockwell's Socket Modems
2 to 4 Wire Converter
Ring Detection
Single +5V Operation
Hookswitch Control
UL and CSA Recognized
Extended Temperature Range Parts available
CONTROL
CURRENT
DETECT
CIRCUIT
CIRCUIT
SWITCH
HOOK-
RING
LINE
RING
TIP
XE0017
XE0017
05/99

Related parts for XE0017

XE0017 Summary of contents

Page 1

... The XE0017 is a complete DAA. It includes a low distortion telephone line transformer, ring detector, hookswitch and 2-4 wire convertor. The 2-4 wire convertor separates transmit and receive signals. The XE0017 operates from a single +5 volt supply and fits in a 0.260 inch high package ...

Page 2

... J 0.090 0.110 2.29 K 0.430 0.450 10.92 Pins are .010 by .020 inches. All Pins are tin-plated for solderability XE0017 Typical Connection Diagram +5 Volts Modem Analog Front End Transmit Receive /Ring OHRLY Recommended Parts Designation Description C1, C2 470 pFd, 3000 Volts (Sprague Part Number 30GA-T47) ...

Page 3

... Ring signal present at Tip and Ring provides the analog output signal from the 2-4 wire converter of the XE0017. 6 N/C No Connection 7 VCC +5 Volt power source provides the analog input signal to the 2-4 wire convertor of the XE0017. 9 GND Ground XECOM Tip 1 XE0017 Ring /RI ...

Page 4

... XE0017 Electrical Specifications Parameter Conditions Power Supply Current XE0017 Off-hook XE0017 On-hook XE0017 Tx Insertion loss 600 Ohm Impedence, 1800 Hz XE0017 Rx Insertion loss 600 Ohm Impedance, 1800 Hz Line Impedance At 1800 Hz XE0017 Transhybrid Loss 600 Ohm Impedance, 1800 Hz Total Harmonic Distortion 600 Ohm Impedance, 1800 Hz Ring Detect Sensitivity Min. AC voltage between Tip & ...

Page 5

... If the system is capable of DTMF dialing, the maximum DTMF transmission level must be less than 0 dBm averaged over a 3 second interval. 4. Billing Delay A delay of 2 seconds or greater is required after the time the XE0017 is taken “off hook” and before any information is transmitted. This is required to ensure that billing information may be exchanged between telephone company central offices without interference. ...

Page 6

... Xecom reserves the right to modify specifications and/or prices without notice. Product mentioned herein are used for identification purposes only and may be trade- marks and/or registered trademarks of their respective companies. XECOM Xecom Incorporated 374 Turquoise Street, Milpitas, CA 95035 Ph:408-945-6640 Fax:408-942-1346 Email: info@xecom.com (6) XE0017 ...

Related keywords