CZP2BFTTE500P KOA Speer Electronics, CZP2BFTTE500P Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/3/373/koa_speer_electronics_sml.jpg)
CZP2BFTTE500P
Manufacturer Part Number
CZP2BFTTE500P
Description
EMI/RFI Suppressors & Ferrites 1206 50ohm 25%
Manufacturer
KOA Speer Electronics
Type
Power Beadr
Series
CZPr
Specifications of CZP2BFTTE500P
Shielding
Shielded
Test Frequency
100MHz
Impedance
50Ohm
Inductance
Not RequireduH
Technology
Multi-Layer
Core Material
Ferrite
Tolerance (+ Or -)
25%
Dc Resistance
25mOhm
Case Size (inches)
1206in
Operating Temp Range
-55C to 125C
Dc Current
4A
Product Diameter (mm)
Not Requiredmm
Product Height (mm)
1.3mm
Product Depth (mm)
1.8mm
Product Length (mm)
3.4mm
Military Standard
Not Required
Failure Rate
Not Required
Dimensions
0.5 mm Dia. x 1.6 mm W x 3.2 mm L x 1.1 mm H
Product
Chip Ferrite Beads
Tolerance
25 %
Maximum Dc Current
3000 mAmps
Maximum Dc Resistance
0.025 Ohms
Operating Temperature Range
- 55 C to + 125 C
Package / Case
1206 (3216 metric)
Termination Style
SMD/SMT
Lead Free Status / RoHS Status
Compliant
5. Characteristics
Bolivar Drive
Spe cific at io ns g ive n herein m ay be ch anged a t any tim e w ith out p rior not ice. Pleas e c onf ir m t echn ic al s pec ifica tions before you order an d/or u se.
Item
Operating Temperature
Storage Temperature
Resistance to Solder
Heat
Solderability
Leach Resistance
Insulation Resistance
Solvent Resistance
Terminal Strength
(hanging test)
Terminal Strength
(push test)
Bending Strength
P.O. Box 547
Requirement
-55°C ~ +125°C
40°C @ 70% Humidity
Change in Impedance: Relative to value before
test ±20%.
Appearance: There shall be no cracking
Solder Coverage: More than 75% of the terminal
electrode shall be covered with solder.
Solder Coverage: More than 95% of the
termination shall be covered with solder.
Appearance: There shall be no visible signs of
physical or mechanical damage (i.e. no cracks).
Terminations: Termination must not be leached
away for more than 5%.
Insulation Resistance: Min 1G ohms
Change in Impedance: Relative to value before
test ±10%.
Appearance: The terminal electrode shall not
break off, nor shall there be damage to the body.
Appearance: There shall be no evidence of
mechanical degradations to terminals or body.
Appearance: There shall be no physical or
mechanical damage.
Impedance: Relative to initial value before test
±10%.
Bradford, PA 16701
USA
814-362-5536
Conditions
Sealed plastic bags with desiccant shall be
used to reduce the potential of oxidation on
the terminations during storage.
Flux: 5-10 sec dip
After Flux: Air dry for 15 sec
Preheat: 150°C ±10°C
Preheat Time: 60 sec
Solder Temp: 260°C ±5°C
Dip Time: 10 ±1 sec
Flux: 5-10 sec dip
After Flux: Air dry for 15 sec
Solder Temp: 245°C ±5°C
Dip Time: 5 ±0.5 sec
The bead shall be subjected to the following
5 steps for the period of time shown below.
The 5 steps constitute one (1) rotation.
4 rotations shall be carried out.
1) Flux: 5-10 sec
2) After Flux: Air dry for 15 sec
3) Solder Temp: 230°C ±5°C
4) Dip Time: 5 ±0.5 sec
5) Cool: Air cool for 60 seconds
Cleaning by:
Washer: Ultrasonic washer (100W)
Solvent: Isopropyl alcohol
Time: 3 minutes
Board: 90x40x1.6mm
Bend: 1mm
Time: 5 sec
Type
Type
Fax 814-362-8883
2A
2B
2A
2B
1J
1J
W(kgf)
W(kgf)
0.5
1.0
1.5
1.4
1.8
2.3
www.koaspeer.com
30 sec ±2 sec
30 sec ±2 sec
30 sec ±2 sec
PAGE 7 OF 10
60 sec
60 sec
60 sec
Time
Time
SS-220 R12