MCP98242T-CE/MNY Microchip Technology, MCP98242T-CE/MNY Datasheet
MCP98242T-CE/MNY
Specifications of MCP98242T-CE/MNY
Related parts for MCP98242T-CE/MNY
MCP98242T-CE/MNY Summary of contents
Page 1
... Sensor • 256 Byte EEPROM for SPD 3.3V _ SDA SCL DD SPD 2010 Microchip Technology Inc. MCP98242 Description: Microchip Technology temperature sensor converts temperature from -40°C and +125° digital word. This sensor meets JEDEC Specification JC42.4 Mobile Platform Memory Module Thermal Sensor Component. It provides an accuracy of ± ...
Page 2
... MCP98242 Notes: DS21996D-page 2 2010 Microchip Technology Inc. ...
Page 3
... HI_WP Thermal Response Note 1: Characterized but not production tested. 2010 Microchip Technology Inc. †Notice: Stresses above those listed under “Maximum ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied ...
Page 4
... GND = Ground. DD Sym Min Typ Max T -20 — +125 A T -40 — +125 A T -65 — +150 A to exceed Maximum Junction Temperature (+150°C). J Conditions Conditions V V µ µ 0. OUTPUT time Units Conditions (Note 1) °C °C °C 2010 Microchip Technology Inc. ...
Page 5
... SU-START Start Condition Hold Time t H-START Stop Condition Setup Time t SU-STOP Bus Idle t B_FREE Time Out t OUT TIMING DIAGRAM Start Condition 2010 Microchip Technology Inc. = 3.0V to 3.6V, GND = Ground. DD Sym Min Typ Max — 84.5 JA — — ...
Page 6
... MCP98242 NOTES: DS21996D-page 6 2010 Microchip Technology Inc. ...
Page 7
... Temperature Accuracy (°C) FIGURE 2-3: Temperature Accuracy Histogram +75°C. A 2010 Microchip Technology Inc. = 3.0V to 3.6V, GND = Ground, SDA/SCL pulled- 10000 1000 EEPROM Write (Sensor in Shutdown Mode) 100 Sensor (EEPROM Inactive) 10 EEPROM Read (Sensor in Shutdown Mode) 1 -40 100 ...
Page 8
... FIGURE 2-12: Response. , and DD = 3.0V to 3.6V = 0.6V - 100 120 T (°C) A SDA IOL vs. Temperature. = 3.0V Δ°C/ΔV = 0.4°C 3.6V - 100 120 T (°C) A Temperature Accuracy vs. TSSOP-8 DFN-8 22°C (Air) to 125°C (Oil bath Time (s) Package Thermal 2010 Microchip Technology Inc. ...
Page 9
... Serial Data Line (SDA) SDA is a bidirectional input/output pin, used to serially transmit data to/from the host controller. This pin Section 4.0 “Serial requires a pull-up resistor. (See Communication”). 2010 Microchip Technology Inc. Table 3-1. Pin Function Slave Address Slave Address ...
Page 10
... MCP98242 NOTES: DS21996D-page 10 2010 Microchip Technology Inc. ...
Page 11
... During normal data transfers, SDA only changes state while SCLK is low. 2010 Microchip Technology Inc. 4.1.1 DATA TRANSFER Data transfers are initiated by a Start condition (Start), followed by a 7-bit device address and a read/write bit. ...
Page 12
... MCP98242 temperature sensor resets the serial interface. This dictates the minimum clock speed as specified in the SMBus specification. However, the EEPROM does not reset the serial interface. Therefore, the master can hold the clock indefinitely to process data from the EEPROM. , OUT 2010 Microchip Technology Inc. ...
Page 13
... Selected Resolution Temp. Range Accuracy Output Feature Register Pointer A0 Event A2 A1 FIGURE 5-1: Functional Block Diagram. 2010 Microchip Technology Inc. registers and a 2-wire I serial interface. Figure 5-1 the register structure. Band-Gap Temperature Sensor Address Decoder ADC 0.5°C/bit 0.25° ...
Page 14
... Register 5-1 describes the pointer or the address of the ambient each register. W-0 W-0 — Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared ) CRIT ) A W-0 W-0 W-0 Pointer Bits bit Bit is unknown ) UPPER ) LOWER 2010 Microchip Technology Inc. ...
Page 15
... MSB CRIT A UPPER 3 2 LSB 2 °C 2 °C 0x06 MSB 0 0 LSB 0 1 0x07 MSB 0 0 LSB 0 0 0x08 LSB 0 0 2010 Microchip Technology Inc. Bit Assignment Resolution Int Clr Evt Stat Evt Cnt 7 0 SIGN 2 ° °C 2 °C 2 ° SIGN 2 ° ...
Page 16
... Meas Range U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared Section 5.2.3.3 “Temperature UPPER U-0 U-0 U-0 — — — bit 8 R-1 R-1 R-1 Accuracy Temp Alarm bit Bit is unknown Resolution” registers) and a LOWER CRIT 2010 Microchip Technology Inc. ...
Page 17
... SCLK SDA Address Byte MCP98242 SCLK A A SDA Address Byte FIGURE 5-2: Timing Diagram for Reading the Capability Register (See Communication”). 2010 Microchip Technology Inc Capability Pointer MCP98242 MSB Data Master MCP98242 MCP98242 LSB Data Master Section 4.0 “Serial ...
Page 18
... Section 5.2.1 “Shutdown sensor circuit stops converting Section 5.2.1 “Shutdown , T and T UPPER LOWER CRIT described in Register 5-3 (see Configuration”). R/W-0 R/W-0 T SHDN HYST bit 8 R/W-0 R/W-0 Event Pol. Event Mod. bit Bit is unknown Section 5.2.3 Mode”) 2010 Microchip Technology Inc. ...
Page 19
... Comparator output (power-up default Interrupt output This bit cannot be altered when either of the lock bits is set (bit 6 and bit 7). 2010 Microchip Technology Inc. register can be written. (power-up default) Default”). This bit does not require a double-write. Window Lock Bit (Win. Lock): and T registers can be written ...
Page 20
... K Configuration Pointer MCP98242 MCP98242 MSB Data LSB Data MCP98242 Configuration Pointer MCP98242 MSB Data Master MCP98242 MCP98242 Note not necessary to select the Register Pointer if it was set from the previous read/ write LSB Data Master 2010 Microchip Technology Inc. ...
Page 21
... CRIT Temperature boundary trip data in two’s complement format. Unimplemented: Read as ‘0’ bit 1-0 Note: This table shows two 16-bit registers for T ‘0000 0011b’ and ‘0000 0100b’, respectively. 2010 Microchip Technology Inc UPPER ) and a LOWER ) that CRIT (Section 5 ...
Page 22
... MSB Data MCP98242 Pointer UPPER MCP98242 MCP98242 MSB Data Master MCP98242 LSB Data MCP98242 Note not necessary to select the Register Pointer if it was set from the previous read/write LSB Data Master Register (See Section 4.0 UPPER 2010 Microchip Technology Inc. ...
Page 23
... Data in 2’s complement format. Depending on the status of the Resolution Register bit 1-0 A these bits may display 2 Note 1: Not affected by the status of the Event output Configuration (bits CONFIG), 2010 Microchip Technology Inc. EQUATION 5-1: Where Ambient Temperature (°C) A Code = MCP98242 temperature output ...
Page 24
... Timing Diagram for Reading +25.25°C Temperature from the T Section 4.0 “Serial Communication”). DS21996D-page Pointer A MCP98242 MSB Data Master MCP98242 Note not necessary to select the Register Pointer if it was set from the previous read/ write LSB Data Master Register (See A 2010 Microchip Technology Inc. ...
Page 25
... A A SDA Address Byte SCLK A A SDA Address Byte FIGURE 5-6: Timing Diagram for Reading the Manufacturer ID Register (See Communication”). 2010 Microchip Technology Inc. R-0 R-0 Manufacturer ID R-1 R-0 Manufacturer Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared Manuf ...
Page 26
... Reading Device ID and Device Revision Register R-0 R-0 R-0 bit 8 R-0 R-0 R-1 bit Bit is unknown Note not necessary to select the Register Pointer if it was set from the previous read/ write LSB Data Master (See Section 4.0 2010 Microchip Technology Inc. ...
Page 27
... SDA Address Byte FIGURE 5-8: Timing Diagram for Changing T Section 4.0 “Serial Communication”). 2010 Microchip Technology Inc. “Temperature U-0 U-0 — — Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared = 30 ms typical typical) CONV = 130 ms typical) CONV = 260 ms typical) ...
Page 28
... Capability register (Register 5-2). A 0.25°C resolution is set as POR default by factory. Figure 5-2 shows device must be operating in ; the T vs. CONV A boundary conditions need CRIT drifts above or below T A UPPER is located in address 2010 Microchip Technology Inc. ...
Page 29
... UPPER UPPER HYST CRIT CRIT HYST When T and T A CRIT CONFIG (Event output mode) is ignored. FIGURE 5-9: Event Output Condition. 2010 Microchip Technology Inc. Samples/sec (typical UPPER HYST T -T LOWER HYST Event Output Comparator Interrupt ...
Page 30
... Figure 5-10 shows the timing diagram SCLK A A SDA Address Byte FIGURE 5-10: Timing Diagram for Byte Write (See DS21996D-page Word Address MCP98242 MCP98242 Section 4.0 “Serial Data MCP98242 Communication”). 2010 Microchip Technology Inc. ...
Page 31
... X Data at (n) MCP98242 Note: FIGURE 5-11: Timing Diagram for Page Write (See 2010 Microchip Technology Inc. Note: Page write operations are limited to writing bytes within a single physical page, regardless of the number of bytes actually being written. Physical page boundaries start at addresses that are integer multiples of the page buffer size (or ‘ ...
Page 32
... ACK X ACK ACK X ACK ACK Address ACK NoACK X NoACK ACK Address ACK Address Byte Slave Address R ACK Write Cycle X ACK Yes Data ACK Yes X NoACK No X ACK Yes X ACK Yes Data NoACK No X NoACK No Data NoACK No 2010 Microchip Technology Inc. ...
Page 33
... A0 pin, apply V HI_WP FIGURE 5-13: Timing Diagram for Setting Clear Write-Protect (See Communication”). 2010 Microchip Technology Inc. The Slave Address bits need to correspond to the address pin logic configuration. For SWP, a high voltage V HI_WP the corresponding slave address needs to be set to ‘1’, ...
Page 34
... However, the address pin states need to match the slave address bits, as shown in Table 5-4 and Word Address MCP98242 MCP98242 is not applied on the A0 pin to execute PWP. HI_WP is not applied on the HI_WP Table 5- Data MCP98242 Section 4.0 “Serial 2010 Microchip Technology Inc. ...
Page 35
... The master will not acknowledge (NAK) the transfer but does generate a Stop condition and the MCP98242 discontinues transmission 1 2 SCLK SDA Note: FIGURE 5-15: Reading Current Word Address (See 2010 Microchip Technology Inc. ACK Address ACK X NoACK X ACK X ACK X NoACK X (Figure 5-15) ...
Page 36
... In this example, ‘n’ is the current Address Word which ‘00’h and the data is the byte at address ‘n’. FIGURE 5-16: Timing Diagram for Random Read (See DS21996D-page Word Address (n) MCP98242 MCP98242 Address Byte Data at (n) MCP98242 Section 4.0 “Serial Master Communication”). 2010 Microchip Technology Inc. ...
Page 37
... This would include any error conditions occurring, such as improper number of clock cycles or improper instruction byte as defined previously. 2010 Microchip Technology Inc. To provide sequential reads, the MCP98242 contains an internal Address Pointer, which is incremented by one at the completion of each operation. This Address Pointer allows the entire memory contents to be serially read during one operation ...
Page 38
... Temperature event output Comparator mode Active-Low output Event and critical output Output disabled Event not asserted Interrupt cleared Event limits unlocked Critical limit unlocked Continuous conversion 0°C Hysteresis 0°C 0°C 0°C 0°C 0x0054 (hex) 0x2001 (hex) 0x01 (hex) 2010 Microchip Technology Inc. ...
Page 39
... Temperature Sensor EEPROM FIGURE 6-2: Multiple Devices on DIMM SMBus. 2010 Microchip Technology Inc. 6.2 Layout Considerations The MCP98242 does not require any additional components besides the master controller in order to measure temperature. However recommended that a decoupling capacitor of 0.1 µ µF be used between the V and GND pins ...
Page 40
... MCP98242 NOTES: DS21996D-page 40 2010 Microchip Technology Inc. ...
Page 41
... Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2010 Microchip Technology Inc. MCP98242 : Example ABJ ...
Page 42
... MCP98242 D N NOTE TOP VIEW A3 DS21996D-page EXPOSED PAD BOTTOM VIEW A NOTE NOTE 2010 Microchip Technology Inc. ...
Page 43
... Microchip Technology Inc. MCP98242 DS21996D-page 43 ...
Page 44
... MCP98242 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS21996D-page 44 2010 Microchip Technology Inc. ...
Page 45
... Microchip Technology Inc. MCP98242 DS21996D-page 45 ...
Page 46
... MCP98242 DS21996D-page 46 2010 Microchip Technology Inc. ...
Page 47
... Microchip Technology Inc. MCP98242 DS21996D-page 47 ...
Page 48
... MCP98242 DS21996D-page 48 2010 Microchip Technology Inc. ...
Page 49
... D N NOTE 2010 Microchip Technology Inc MCP98242 φ L DS21996D-page 49 ...
Page 50
... MCP98242 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS21996D-page 50 2010 Microchip Technology Inc. ...
Page 51
... Updated Figure 5-9. Section 7.0 “Packaging Information”: 7. Updated package outline drawings. Revision B (February 2008) The following is the list of modifications: 1. Added TDFN package throughout document. Revision A (September 2006) • Original Release of this Document. 2010 Microchip Technology Inc. ID and MCP98242 DS21996D-page 51 ...
Page 52
... MCP98242 NOTES: DS21996D-page 52 2010 Microchip Technology Inc. ...
Page 53
... MCP98242-BE/MC: Extended Temp., 8LD DFN pkg. MCP98242T-BE/MC: Tape and Reel, Extended Temp., 8LD DFN pkg. MCP98242-BE/ST: Extended Temp., 8LD TSSOP pkg. MCP98242T-BE/ST: Tape and Reel, Extended Temp., 8LD TSSOP pkg. MCP98242-BE/MNY: Extended Temp., 8LD TDFN (nickel palladium gold) pkg. MCP98242-BE/MUY: Extended Temp., ...
Page 54
... MCP98242 NOTES: DS21996D-page 54 2010 Microchip Technology Inc. ...
Page 55
... PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 56
... Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-213-7830 Fax: 886-7-330-9305 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 2010 Microchip Technology Inc. 08/04/10 ...