MIC2292C-15YML TR Micrel Inc, MIC2292C-15YML TR Datasheet
MIC2292C-15YML TR
Specifications of MIC2292C-15YML TR
Related parts for MIC2292C-15YML TR
MIC2292C-15YML TR Summary of contents
Page 1
... General Description The MIC2292C and MIC2293C are high frequency, Pulse Width Modulator (PWM) boost regulators optimized for constant-current, white LED driver applications. Because of their constant PWM switching frequencies of 1.6MHz and 2MHz, respectively, the MIC2292/93C can use the smallest external components, allowing designers to avoid sensitive IF bands in their RF applications ...
Page 2
... Micrel, Inc. Ordering Information Marking Part Number Code MIC2292C-15YML MIC2293C-34YML Notes 1: Contact Micrel Marketing for other voltage options. Pin Configuration Pin Description Pin Number Pin Name 1 OUT 2 VIN AGND PGND EP GND September 2009 Overoltage Junction Protection Temp. Range 15V –40°C to +125°C 34V – ...
Page 3
... FB 3V ≤ V ≤ 5mA ≤ I ≤ 20mA OUT 10V EN SW TURN ON TURN OFF V = 10V EN MIC2292C MIC2293C I = 150mA 30V R MIC2292/93C-15 MIC2292/93C-34 Hysteresis , and the ambient temperature The maximum allowable power dissipation will result in excessive die (2) )........................................ 2.5V to +10V IN ) ............................................ ........................ –40°C to +125°C J ® ...
Page 4
... Micrel, Inc. Typical Characteristics MIC2292C 3 Series LED Efficiency µ µ (mA) LED MIC2293C 6 Series LED Efficiency µ µ (mA) OUT Quiescent Current vs. Input Current 02468 (V) IN Schottky Forward Voltage Drop 700 600 500 400 300 200 100 0 SCHOTTKY FORWARD VOLTAGE DROP (mV) September 2009 ...
Page 5
Micrel, Inc. Typical Characteristics Current Limit vs. Temperature 900 850 800 750 700 650 V = 2.5V IN 600 - 120 TEMPERATURE (°C) September 2009 Switch Frequency vs. Temperature 2 1.6 1.2 0.8 0.4 0 -40 04 ...
Page 6
Micrel, Inc. Functional Characteristics 6-Series LED Circuit with External Soft-Start September 2009 6-Series LED Circuit without External Soft-Start L = 10µ 1µ 0.22µF OUT 20mA OUT 6 LEDs C ...
Page 7
... PWM generator, 500mA bipolar output transistor, and Schottky rectifier diode. The oscillator generates a 1.6MHz clock for the MIC2292C and a 2.0MHz clock for the MIC2293C. The clocks' two functions are to trigger the PWM generator that turns on ...
Page 8
Micrel, Inc. External Component Selection The MIC2292/93C can be used across a wide rage of applications. The table below shows recommended Series LEDs L 2 22µH 15µH 10µH 6.8µH 4.7µH 3 22µH 15µH 10µH 6.8µH 4.7µH 4 22µH 15µH 10µH ...
Page 9
Micrel, Inc. Dimming Control There are two techniques for dimming control. One is PWM dimming, and the other is continuous dimming. 1. PWM dimming control is implemented by applying a PWM signal on EN pin as shown in Figure 1. ...
Page 10
Micrel, Inc. Package Information MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. ...