MIC2342R-2YTQ Micrel Inc, MIC2342R-2YTQ Datasheet - Page 7

• Manufacturer Part Number: MIC2342R-2YTQ
• Description: Dual -Slot PCI Express Hot-Plug Controller
• Manufacturer: Micrel Inc
• Type: Hot-Swap Controllerr

Specifications of MIC2342R-2YTQ

• Applications: General Purpose, PCI Express
• Internal Switch(s): No
• Current Limit: Adjustable
• Voltage - Supply: 3.3V, 12V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 48-TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 576-2996

Pin Description (cont.)
Micrel, Inc.
June 2008
Pin Number
36
39
48
37
28
1
4
9
/FAULT_MAINA
/FAULT_MAINB
/FAULT_AUXA
/FAULT_AUXB
/FORCE_ONA
/FORCE_ONB
Pin Name
/CRSWA
/CRSWB
Pin Function
/FAULT_MAIN[A/B] Outputs are open-drain, asserted active-LOW digital outputs
that are normally connected by an external 10kΩ resistor to VSTBY. Asserted
whenever the primary or secondary circuit breaker trips because of an overcurrent
fault condition or an input undervoltage. Applying a high-to-low transition at the
ON[A/B] pin resets the /FAULT_MAIN[A/B] outputs if /FAULT_MAIN[A/B] was
asserted in response to a fault condition on one of the slot’s MAIN outputs (+12V or
+3.3V). If an overcurrent event asserted /FAULT_MAIN[A/B], the respective output’s
circuit breaker is reset when
/FAULT_MAIN[A/B] output signal is de-asserted. A 200ns minimum pulse width
(t
once the fault is removed.
If a fault condition occurred on both the MAIN and VAUX outputs of the same slot,
then a high-to-low transition on both ON[A/B] and AUXEN[A/B] must be applied to
de-assert the /FAULT_MAIN[A/B] and /FAULT_AUX[A/B] outputs.
To simplify system fault reporting, the /FAULT_MAIN[A/B] output pins may be
connected together with the /FAULT_AUX[A/B] output pins.
Card Retention Switch Inputs [A/B]. These are level sensitive, asserted active- LOW
digital inputs with internal pull-up resistors to VSTBY[A]. These inputs can be
connected to the PRNST#1 or PRNST#2 pins on a PCIe connector to indicate to the
MIC2342 that a PCIe plug-in card is present and firmly mated. Internally, the
MIC2342’s +12VGATE[A/B], +3VGATE[A/B], and 3VAUX[A/B] gate drive circuits are
gated with the MIC2342’s ON[A/B] and the AUXEN[A/B] inputs to deliver power to
the connector only when a PCIe plug-in card is present. During operation, if the
/CRSW[A/B] inputs are disconnected or if there is a pc board trace failure, all
outputs on the respective slot are turned OFF without delay. Each of these inputs
exhibit an internal switch debounce delay of approximately 10ms.
/FAULT_AUX[A/B] Outputs are open-drain, asserted active-LOW digital outputs that
are normally connected by an external 10kΩ resistor to VSTBY. Asserted whenever
the VAUX[A/B] circuit breaker trips because of an overcurrent fault condition or a
slot/die overtemperature condition. Applying a high-to-low transition at the
AUXEN[A/B] pin for at least 0.5µs resets the /FAULT_AUX[A/B] outputs if the
/FAULT_AUX[A/B] output signal was asserted in response to a fault condition on the
respective slot’s VAUX output. If an overcurrent event asserted /FAULT_AUX[A/B],
the respective output’s VAUX circuit breaker is reset when /FAULT_AUX[A/B] output
signal is de-asserted. A 200ns minimum pulse width (t
reset the MAIN outputs in the event of an overcurrent fault once the fault is
removed.
If a fault condition occurred on both the MAIN and VAUX outputs of the same slot,
then a high-to-low transition on both ON[A/B] and AUXEN[A/B] must be applied to
de-assert the /FAULT_MAIN[A/B] and /FAULT_AUX[A/B] outputs.
To simplify system fault reporting, the /FAULT_AUX[A/B] output pins may be
connected together with the /FAULT_MAIN[A/B] output pins.
Force On Enable Inputs [A/B]: These active-LOW, level-sensitive inputs with internal
pull-up current (µA) to VSTBY[A] will turn on all three of the respective slot’s outputs
(+12V, +3.3V, and VAUX), while specifically defeating all protections on those
supplies when asserted. This explicitly includes all overcurrent and short circuit
protections and on-chip thermal protection for the VAUX[A/B] supplies. Additionally
included are the UVLO protections for the +3.3V and +12V main supplies. The
/FORCE_ON[A/B] pins do not disable UVLO protection for the VAUX[A/B] supplies.
These input pins are intended for diagnostic purposes only.
Asserting /FORCE_ON[A/B] will cause the respective slot’s /PWRGD[A/B] and
/DLY_PWRGD[A/B] output signals to be asserted LOW and cause the
/FAULT_MAIN[A/B], the /FAULT_AUX[A/B], the /INT, and the SYSPWRGD output
signals to their open-drain state.
LPW
) for ON[A/B] will reset the MAIN outputs in the event of an overcurrent fault
7
LPW
) for AUX_EN[A/B] will
MIC2342/2342R
M9999-062008-B