MIC5211-LXYM6 TR Micrel Inc, MIC5211-LXYM6 TR Datasheet - Page 3

• Manufacturer Part Number: MIC5211-LXYM6 TR
• Description: MIC5211-3.3/5.0YM6 Dual Cap 50mA LDO ( )
• Manufacturer: Micrel Inc

Specifications of MIC5211-LXYM6 TR

• Regulator Topology: Positive Fixed
• Voltage - Output: 3.3V, 5V
• Voltage - Input: 2.5 ~ 16 V
• Voltage - Dropout (typical): 0.25V @ 50mA
• Number Of Regulators: 2
• Current - Output: 50mA
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 576-2749-2; MIC5211-LXYM6 TR; MIC5211-LXYM6TR; MIC5211-LXYM6TR

MIC5211
Absolute Maximum Ratings (Note 1)
Supply Input Voltage (V
Enable Input Voltage (V
Power Dissipation (P
Storage Temperature Range .................... –60°C to +150°C
Lead Temperature (soldering, 5 sec.) ........................ 260°C
ESD, (Note 3) ......................................................................
Electrical Characteristics
V
for one-half of dual MIC5211; unless noted.
Symbol
V
ΔV
ppm/°C
ΔV
ΔV
V
I
I
I
ΔV
Enable Input
V
V
I
I
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
May 2006
Q
GND
LIMIT
IL
IH
IN
O
IN
IL
IH
O
O
O
O
= V
– V
/ΔT
/V
/V
/ΔP
O
O
O
OUT
D
Exceeding the absolute maximum rating may damage the device.
The device is not guareented to function outside itsperating rating.
Devices are ESD sensitive. Handling precautions recommended.
The maximum allowable power dissipation at any T
able power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. The θ
SOT-23-6 mounted on a printed circuit board.
Output voltage temperature coeffiecient is defined as the worst case voltage change divided by the total temperature range.
Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load
range from 0.1mA to 50mA. Change in output voltage due to heating effects are covered by thermal regulation specification.
Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V
differential. For output voltages below 2.5V, dropout voltage is the input-to-output voltage differential with the minimum voltage being 2.5V.
Minimum input opertating voltage is 2.5V.
Ground pin current is the quiescent current per regulator plus pass transistor base current. The total current drawn from the supply is the sum
of the load current plus the ground pin current.
Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line
regulation effects. Specifications are for a 50mA load pulse at V
+ 1V; I
Parameter
Output Voltage
Accuracy
Output Voltage
Temperature Coeffcient
Line Regulation
Load Regulation
Dropout Voltage, Note 7
Quiescent Current
Ground Pin Current
Note 8
Current Limit
Thermal Regulation
Enable Input Voltage Level
Enable Input Current
L
= 1mA; C
D
) ............................. Internally Limited
IN
EN
) ..............................–20V to +20V
) ............................–20V to +20V
L
= 0.1µF, and V
EN
≥ 2.0V; T
Conditions
variation from nominal V
Note 5
V
I
I
I
I
V
V
I
I
V
Note 9
logic low (off)
logic high (on)
V
V
A
L
L
L
L
L
L
IN
EN
EN
OUT
IL
IH
(ambient temperature) is P
= 0.1mA to 50mA, Note 6
= 50mA
= 100µA
= 20mA
= 20mA (active)
= 50mA (active)
J
≤ 0.6V
= V
≥ 2.0V
≤ 0.4V (shutdown)
≥ 2.0V, I
= 25°C, bold values indicate –40°C to +125°C;
= 0V
OUT
IN
+1V to 16V
L
3
= 16V for t = 10ms.
= 100µA (active)
Operating Ratings (Note 2)
Supply Input Voltage (V
Enable Input Voltage (V
Junction Temperature (T
6-lead SOT-23-6 (θ
1.8V only ................................................... 0°C to +125°C
OUT
D(max)
= (T
J(max)
JA
) ............................................. Note 4
– T
IN
EN
J
A
) .................................2.5V to 16V
) (except 1.8V) .. –40°C to +125°C
) / θ
) ..................................0V to 16V
JA
Min
2.0
–3
–4
. Exceeding the maximum allow-
Typical
0.008
0.08
0.01
0.05
0.01
200
250
225
750
140
50
20
90
JA
3
is 220°C/W for the
1200
Max
200
450
500
450
250
0.3
0.5
0.3
0.5
0.6
10
50
3
4
1
Micrel, Inc.
MIC5211
Units
%/W
mV
mV
mV
mA
µA
µA
µA
µA
µA
µA
%
%
%
%
%
%
V
V