MIC5305-2.8YD5 TR Micrel Inc, MIC5305-2.8YD5 TR Datasheet

Page 1

... Equipped with a logic-compatible enable pin, the MIC5305 can be put into a zero-off-mode current state, drawing no current when disabled. The MIC5305 is a µCap design operating with very small ceramic output capacitors for stability, thereby reducing required board space and component cost ...

Page 2

... MIC5305-2.9YML MIC5305-3.0BML MIC5305-3.0YML MIC5305-3.3BML MIC5305-3.3YML MIC5305-4.75BML MIC5305-4.75YML MIC5305BML MIC5305YML MIC5305-2.8YMT MIC5305-4.6YMT MIC5305-1.5BD5 MIC5305-1.5YD5 MIC5305-1.8BD5 MIC5305-1.8YD5 MIC5305-2.5BD5 MIC5305-2.5YD5 MIC5305-2.6BD5 MIC5305-2.6YD5 MIC5305-2.7BD5 MIC5305-2.7YD5 MIC5305-2.8BD5 MIC5305-2.8YD5 MIC5305-2.85BD5 MIC5305-2.85YD5 MIC5305-2.9BD5 MIC5305-2.9YD5 MIC5305-3.0BD5 MIC5305-3.0YD5 MIC5305-3.3BD5 MIC5305-3.3YD5 MIC5305-4.75BD5 MIC5305-4.75YD5 Note: 1. For other output voltage options, contact Micrel marketing. ...

Page 3

... EN GND VIN KWxx 4 5 BYP VOUT MIC5305-x.xBD5/YD5 (Fixed) TSOT-23-5 (D5) (Top View) Pin Name Enable Input. Active High. High = on, low = off. Do not leave floating. Ground. Supply Input. Output Voltage. Adjust Input: Connect to external resistor voltage divider network. No connection for fixed voltage parts. ...

Page 4

... JA Thin MLF-6 (θ ) ................................................93°C/W JA TSOT-23-5 (θ ) ..............................................235°C/W JA Min Typ –1.0 –2.0 0.02 0.1 0.5 = 0.1µF 600 300 1.0 0.01 0. θ . Exceeding the maximum allowable power D(max) J(max OUT MIC5305 IN Max Units +1 +2.0 40 pm/°C %/V 0 110 90 µA 150 µA ...

Page 5

... FREQUENCY (kHz) Ground Pin Current -40 -20 0 TEMPERATURE (°C) Dropout Characteristics 3 100µA LOAD 3 2.5 2 1 INPUT VOLTAGE (V) Dropout Voltage 100 -40 -20 0 TEMPERATURE (°C) MIC5305 PSRR 150mA 50mA 10 100 150mA LOAD 100 120 I = 150mA LOAD 100mA OUT 100 120 M9999-062507 ...

Page 6

... OUTPUT CURRENT (mA) Enable Threshold vs. Temperature 1 0.9 0.8 0.7 0.6 0.5 0 100µA LOAD 0.3 -40 - 100 120 TEMPERATURE (°C) 6 MIC5305 Short Circuit Current 800 700 600 500 400 300 200 100 0 3 3.5 4 4.5 5 5.5 6 INPUT VOLTAGE (V) Output Noise Spectral Density ...

Page 7

... BYP I = 100µA OUT C = 1µF Ceramic OUT C = 0.01µF BYP I = 100µA OUT C = 1µF Ceramic 1µF Ceramic OUT 7 MIC5305 Load Transient Response C = 0.01µF BYP 1µF Ceramic OUT TIME (4µs/div) Shutdown Delay C = 0.01µF BYP I = 100µA OUT ...

Page 8

... Micrel, Inc. Functional Diagram VIN EN BYP VIN EN BYP June 2007 Quick- V REF Start Thermal Shutdown MIC5305 Block Diagram – Fixed Quick- V REF Start Error LDO Amp Thermal Shutdown Current MIC5305 Block Diagram – Adjustable 8 VOUT Error LDO Amp Current Limit GND ...

Page 9

... Micrel, Inc. Application Information Enable/Shutdown The MIC5305 comes with an active-high enable pin that allows the regulator to be disabled. Forcing the enable pin low disables the regulator and sends it into a “zero” off-mode-current state. In this state, current consumed by the regulator goes nearly to zero. Forcing the enable pin high enables the output voltage ...

Page 10

... Micrel, Inc. Table 1 shows junction-to-ambient thermal resistance for the MIC5305 in the 6-pin 2mm × 2mm MLF θ JA Recommended Package Minimum Footprint ® 6-Pin 2x2 MLF 93°C/W Table 1. Thermal Resistance Substituting P for P and solving for the ambient D D(max) operating temperature will give the maximum operating conditions for the regulator circuit ...

Page 11

... Micrel, Inc. Package Information June 2007 ® 6-Pin 2x2 MLF (ML) ® 6-Pin 2x2 Thin MLF (MT) 11 MIC5305 M9999-062507 ...

Page 12

... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully June 2007 5-Pin TSOT-23 (D5) indemnify Micrel for any damages resulting from such use or sale. © 2004 Micrel, Incorporated. 12 MIC5305 M9999-062507 ...