PIC18LF4458T-I/ML Microchip Technology, PIC18LF4458T-I/ML Datasheet - Page 28
![24KB Flash, 2KB RAM, 256 Bytes EEPROM, 35 I/O, USB, 12bit ADC 44 QFN 8x8x0.9mm T](/photos/6/81/68122/150-44-qfn_sml.jpg)
PIC18LF4458T-I/ML
Manufacturer Part Number
PIC18LF4458T-I/ML
Description
24KB Flash, 2KB RAM, 256 Bytes EEPROM, 35 I/O, USB, 12bit ADC 44 QFN 8x8x0.9mm T
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC18F2221-ISO.pdf
(46 pages)
2.PIC18F2458-ISO.pdf
(46 pages)
3.PIC18F2458-ISO.pdf
(6 pages)
4.PIC18F2458-ISO.pdf
(6 pages)
5.PIC18F2458-ISO.pdf
(6 pages)
Specifications of PIC18LF4458T-I/ML
Core Processor
PIC
Core Size
8-Bit
Speed
48MHz
Connectivity
I²C, SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
35
Program Memory Size
24KB (12K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 13x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PIC18F2458/2553/4458/4553
2.4
The selection of the automatic acquisition time and A/D
conversion clock is determined in part by the clock
source and frequency while in a power-managed mode.
If the A/D is expected to operate while the device is in
a power-managed mode, the ADCS2:ADCS0 bits in
ADCON2 should be updated in accordance with the
clock source to be used. The ACQT2:ACQT0 bits do
not need to be adjusted as the ADCS2:ADCS0 bits
adjust the T
entering the mode, an A/D acquisition or conversion
may be started. Once started, the device should
continue to be clocked by the same clock source until
the conversion has been completed.
If desired, the device may be placed into the
corresponding Idle mode during the conversion. If the
device clock frequency is less than 1 MHz, the A/D RC
clock source should be selected.
Operation in Sleep mode requires the A/D F
be selected. If bits ACQT2:ACQT0 are set to ‘000’ and
a conversion is started, the conversion will be delayed
one instruction cycle to allow execution of the SLEEP
instruction and entry to Sleep mode. The IDLEN bit
(OSCCON<7>) must have already been cleared prior
to starting the conversion.
DS39887C-page 28
Operation in Power-Managed
Modes
AD
time for the new clock speed. After
RC
clock to
2.5
The ADCON1, TRISA, TRISB and TRISE registers all
configure the A/D port pins. The port pins needed as
analog inputs must have their corresponding TRIS bits
set (input). If the TRIS bit is cleared (output), the digital
output level (V
The A/D operation is independent of the state of the
CHS3:CHS0 bits and the TRIS bits.
Note 1: When reading the PORT register, all pins
2: Analog levels on any pin defined as a dig-
3: The
Configuring Analog Port Pins
configured as analog input channels will
read as cleared (a low level). Analog con-
version on pins configured as digital pins
can be performed. The voltage on the pin
will be accurately converted.
ital input may cause the digital input buffer
to consume current out of the device’s
specification limits.
Register 3H configures PORTB pins to
reset as analog or digital pins by control-
ling how the PCFG3:PCFG0 bits in
ADCON1 are reset.
OH
or V
PBADEN
OL
© 2009 Microchip Technology Inc.
) will be converted.
bit
in
Configuration