STK14C88-5C35M Cypress Semiconductor Corp, STK14C88-5C35M Datasheet - Page 10
![STK14C88-5C35M](/photos/28/21/282144/32-cdip_sml.jpg)
STK14C88-5C35M
Manufacturer Part Number
STK14C88-5C35M
Description
STK14C88-5C35M
Manufacturer
Cypress Semiconductor Corp
Datasheet
1.STK14C88-C45I.pdf
(19 pages)
Specifications of STK14C88-5C35M
Format - Memory
RAM
Memory Type
NVSRAM (Non-Volatile SRAM)
Memory Size
256K (32K x 8)
Speed
35ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
-55°C ~ 125°C
Package / Case
32-CDIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STK14C88-5C35M
Manufacturer:
a
Quantity:
137
nvSRAM Operation
The STK14C88 has two separate modes of operation: SRAM
mode and nonvolatile mode. In SRAM mode, the memory
operates as a standard fast static RAM. In nonvolatile mode,
data is transferred from SRAM to nonvolatile elements (the
STORE operation) or from nonvolatile elements to SRAM (the
RECALL operation). In this mode, SRAM functions are disabled.
Noise Considerations
The STK14C88 is a high speed memory and so must have a high
frequency bypass capacitor of approximately 0.1 μF connected
between V
as possible. As with all high speed CMOS ICs, careful routing of
power, ground, and signals helps to prevent noise problems.
SRAM Read
The STK14C88 performs a read cycle whenever E and G are
low, and W and HSB are high. The address specified on pins
A
When the read is initiated by an address transition, the outputs
are valid after a delay of t
initiated by E or G, the outputs are valid at t
whichever is later (Read cycle #2). The data outputs repeatedly
respond to address changes within the t
without the need for transitions on any control input pins, and
remain valid until another address change or until E or G is
brought high, or W or HSB is brought low.
SRAM Write
A write cycle is performed whenever E and W are low, and HSB
is high. The address inputs must be stable prior to entering the
write cycle and must remain stable until either E or W goes high
at the end of the cycle. The data on the common I/O pins DQ
are written into the memory if it is valid t
a W controlled write or t
write.
Keep G high during the entire write cycle to avoid data bus
contention on common I/O lines. If G is left low, internal circuitry
turns off the output buffers t
Power Up RECALL
During power up, or after any low power condition (V
V
again exceeds the sense voltage of V
is automatically initiated and takes t
If the STK14C88 is in a write state at the end of power up
RECALL, the SRAM data will be corrupted. To avoid this, a 10
KOhm resistor should be connected either between W and
system V
Document Number: 001-52038 Rev. *B
0-14
RESET
determines which of the 32,768 data bytes are accessed.
), an internal RECALL request is latched. When V
CC
CAP
or between E and system V
and V
SS
, using leads and traces that are as short
DVEH
AVQV
WLQZ
before the end of an E controlled
(Read cycle #1). If the read is
after W goes low.
RESTORE
SWITCH
DVWH
CC
.
AVQV
to complete.
, a RECALL cycle
ELQV
before the end of
access time
or at t
CAP
GLQV
CAP
0-7
<
,
Software Nonvolatile STORE
The STK14C88 software STORE cycle is initiated by executing
sequential E controlled read cycles from six specific address
locations. During the STORE cycle an erase of the previous
nonvolatile data is first performed, followed by a program of the
nonvolatile elements. The program operation copies the SRAM
data into nonvolatile memory. When a STORE cycle is initiated,
further input and output are disabled until the cycle is completed.
Because a sequence of reads from specific addresses is used
for STORE initiation, it is important that no other read or write
accesses intervene in the sequence, or the sequence will be
aborted and no STORE or RECALL takes place.
To initiate the software STORE cycle, the following read
sequence must be performed:
The software sequence must be clocked with E controlled reads.
After the sixth address in the sequence is entered, the STORE
cycle commences and the chip is disabled. Use only read cycles
in the sequence, although it is not necessary that G be low for
the sequence to be valid. After the tSTORE cycle time is fulfilled,
the SRAM is again activated for read and write operation.
Software Nonvolatile RECALL
A software RECALL cycle is initiated with a sequence of read
operations in a manner similar to the software STORE initiation.
To initiate the RECALL cycle, the following sequence of E
controlled read operations must be performed:
Internally, RECALL is a two step procedure. First, the SRAM data
is cleared, and second, the nonvolatile information is transferred
into the SRAM cells. After the t
again ready for read and write operations. The RECALL
operation in no way alters the data in the nonvolatile elements.
The nonvolatile data can be recalled an unlimited number of
times.
AutoStore Mode
The STK14C88 can be powered in one of three modes.
During normal AutoStore operation, the STK14C88 draws
current from V
pin. This stored charge is used by the chip to perform a single
STORE operation. After power up, when the voltage on the V
pin drops below V
V
1. Read address 0E38 (hex) Valid READ
2. Read address 31C7 (hex) Valid READ
3. Read address 03E0 (hex) Valid READ
4. Read address 3C1F (hex) Valid READ
5. Read address 303F (hex) Valid READ
6. Read address 0FC0 (hex) Initiate STORE cycle
1. Read address 0E38 (hex) Valid READ
2. Read address 31C7 (hex) Valid READ
3. Read address 03E0 (hex) Valid READ
4. Read address 3C1F (hex) Valid READ
5. Read address 303F (hex) Valid READ
6. Read address 0C63 (hex) Initiate RECALL cycle
CAP
pin from V
CC
CC
SWITCH
to charge a capacitor connected to the V
and initiate a STORE operation.
, the part automatically disconnects the
RECALL
cycle time, the SRAM is
STK14C88
Page 10 of 19
CAP
CAP
[+] Feedback
[+] Feedback
[+] Feedback