ADV7185KSTZ Analog Devices Inc, ADV7185KSTZ Datasheet - Page 8

• Manufacturer Part Number: ADV7185KSTZ
• Manufacturer: Analog Devices Inc

Specifications of ADV7185KSTZ

• Adc/dac Resolution: 10b
• Screening Level: Commercial
• Package Type: LQFP
• Pin Count: 80
• Lead Free Status / RoHS Status: Compliant

ADV7185
Pin
39, 40, 47, 53,
56, 63
41, 43, 45, 57,
59, 61
42, 44, 46, 58,
60, 62
48, 49
50
51
52
54, 55
64
65
66
67
68
69
70
77
78
79
80
Mnemonic
AVSS
AVSS1–AVSS6
AIN1–AIN6
CAPY1–CAPY2
AVDD
REFOUT
CML
CAPC1–CAPC2
RESET
ISO
ALSB
SDATA
SCLOCK
VREF/VRESET
HREF/HRESET
RD
DV
OE
FIELD
I
I
P
O
I
I
I/O
I
Input/Output
G
G
O
I
I
O
O
I
O
I
O
PIN FUNCTION DESCRIPTIONS (continued)
Function
Ground for Analog Supply
Analog Input Channels. Ground if single-ended mode is selected. These pins
should be connected directly to REFOUT when differential mode is selected.
Video Analog Input Channels
ADC Capacitor Network
Analog Supply Voltage (5 V)
Internal Voltage Reference Output
Common-Mode Level for ADC
ADC Capacitor Network
System Reset Input. Active Low
Input Switch Over. A low to high transition on this input indicates to the
decoder core that the input video source has been changed externally and
configures the decoder to reacquire the new timing information of the new
source. This is useful in applications where external video muxes are used.
This input gives the advantage of faster locking to the external muxed
video sources. A low to high transition triggers this input.
TTL Address Input. Selects the MPU address:
MPU Port Serial Data Input/Output
MPU Port Serial Interface Clock Input
VREF or Vertical Reference Output Signal. Indicates start of next field.
VRESET or Vertical Reset Output is a signal that indicates the beginning
of a new field. In SCAPI/CAPI mode this signal is one clock wide and
active low relative to CLKIN. It immediately follows the HRESET pixel,
and indicates that the next active pixel is the first active pixel of the next field.
HREF or Horizontal Reference Output Signal. A dual-function pin
(enabled when Line-Locked Interface is selected, OM_SEL[1:0] = 0,0),
this signal is used to indicate data on the YUV output. The positive slope
indicates the beginning of a new active line, HREF is always
720 Y samples long. HRESET or Horizontal Reset Output (enabled when
SCAPI or CAPI is selected, OM_SEL[1:0] = 0, 1 or 1, 0) is a signal that
indicates the beginning of a new line of video. In SCAPI/CAPI this signal
is one clock cycle wide and is output relative to CLKIN. It immediately
follows the last active pixel of a line. The polarity is controlled via PHVR.
Asynchronous FIFO Read Enable Signal. A logical high on this pin
enables a read from the output of the FIFO.
DV or Data Valid Output Signal. In SCAPI/CAPI mode, DV performs
two functions, depending on whether SCAPI or CAPI is selected. It
toggles high when the FIFO has reached the AFF margin set by the user,
and remains high until the FIFO is empty. The alternative mode is where
it can be used to control FIFO reads for bursting information out of the
FIFO. In API mode DV indicates valid data in the FIFO, which includes
both pixel information and control codes. The polarity of this pin is con-
trolled via PDV.
Output Enable Controls Pixel Port Outputs. A logic high will three-state
P19–P0.
ODD/EVEN Field Output Signal. An active state indicates that an even field
is being digitized. The polarity of this signal is controlled by the PF bit.
MPU address = 88h ALSB = 0, disables I
MPU address = 8Ah ALSB = 1, enables I
–8–
2
2
C filter
C filter
REV. 0