AD5235BRU250-RL7 Analog Devices Inc, AD5235BRU250-RL7 Datasheet - Page 22

• Manufacturer Part Number: AD5235BRU250-RL7
• Manufacturer: Analog Devices Inc

Specifications of AD5235BRU250-RL7

• Number Of Elements: 2
• # Of Taps: 1024
• Resistance (max): 250KOhm
• Power Supply Requirement: Single/Dual
• Interface Type: Serial (4-Wire/SPI)
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): ±2.5V
• Single Supply Voltage (min): 3V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): ±2.25V
• Dual Supply Voltage (max): ±2.75V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Lead Free Status / RoHS Status: Not Compliant

AD5235
APPLICATIONS INFORMATION
BIPOLAR OPERATION FROM DUAL SUPPLIES
The AD5235 can be operated from ±2.5 V dual supplies, which
enable control of ground referenced ac signals or bipolar operation.
AC signals as high as V
Terminal A to Terminal B with the output taken from Terminal W.
See Figure 45 for a typical circuit connection.
GAIN CONTROL COMPENSATION
A digital potentiometer is commonly used in gain control such
as the noninverting gain amplifier shown in Figure 46.
When the RDAC B terminal parasitic capacitance is connected
to the op amp noninverting node, it introduces a zero for the 1/β
term with 20 dB/dec, whereas a typical op amp gain bandwidth
product (GBP) has −20 dB/dec characteristics. A large R2 and
finite C1 can cause the frequency of this zero to fall well below
the crossover frequency. Therefore, the rate of closure becomes
40 dB/dec, and the system has a 0° phase margin at the crossover
frequency. If an input is a rectangular pulse or step function, the
output can ring or oscillate. Similarly, it is also likely to ring when
switching between two gain values; this is equivalent to a stop
change at the input.
Depending on the op amp GBP, reducing the feedback resistor
might extend the frequency of the zero far enough to overcome
the problem. A better approach is to include a compensation
capacitor, C2, to cancel the effect caused by C1. Optimum
compensation occurs when R1 × C1 = R2 × C2. This is not
an option because of the variation of R2. As a result, one can
use the previous relationship and scale C2 as if R2 were at its
maximum value. Doing this might overcompensate and
compromise the performance when R2 is set at low values.
CONTROLLER
V
DD
MICRO-
GND
SCLK
MOSI
SS
Figure 45. Bipolar Operation from Dual Supplies
Figure 46. Typical Noninverting Gain Amplifier
47kΩ
R1
11pF
C1
DD
CS
CLK
SDI
GND
AD5235
V
and V
I
SS
2.2pF
U1
C2
can be applied directly across
250kΩ
B
V
V
W
R2
SS
DD
W
A
B
A
±1.25V p-p
V
O
D = MIDSCALE
±2.5V p-p
+2.5V
–2.5V
Rev. C | Page 22 of 28
O
Alternatively, it avoids the ringing or oscillation at the worst
case. For critical applications, find C2 empirically to suit the
oscillation. In general, C2 in the range of a few picofarads to no
more than a few tenths of picofarads is usually adequate for the
compensation.
Similarly, W and A terminal capacitances are connected to the
output (not shown); their effect at this node is less significant
and the compensation can be avoided in most cases.
HIGH VOLTAGE OPERATION
The digital potentiometer can be placed directly in the feedback or
input path of an op amp for gain control, provided that the voltage
across Terminal A to Terminal B, Terminal W to Terminal A or
Terminal W to Terminal B does not exceed |5 V|. When high
voltage gain is needed, set a fixed gain in the op amp and let the
digital potentiometer control the adjustable input. Figure 47
shows a simple implementation.
Similarly, a compensation capacitor, C, may be needed to dampen
the potential ringing when the digital potentiometer changes
steps. This effect is prominent when stray capacitance at the
inverted node is augmented by a large feedback resistor. Typically,
a picofarad Capacitor C is adequate to combat the problem.
DAC
For DAC operation (see Figure 48), it is common to buffer the
output of the digital potentiometer unless the load is much larger
than R
conversion and can drive heavier loads.
WB
. The buffer serves the purpose of impedance
AD5235
GND
1
2
V
5V
IN
Figure 47. 15 V Voltage Span Control
U1
AD1582
V
OUT
Figure 48. Unipolar 10-Bit DAC
5V
3
A
B
R
AD5235
W
A
B
W
AD8601
A1
A1
15V
V+
V–
V+
V–
5V
2R
C
0V TO 15V
V
V
O
O