HA1-2425-5 Intersil, HA1-2425-5 Datasheet
HA1-2425-5
Specifications of HA1-2425-5
Available stocks
Related parts for HA1-2425-5
HA1-2425-5 Summary of contents
Page 1
... For more information, please see Application Note AN517.. Ordering Information TEMP. o PART NUMBER RANGE ( C) PACKAGE HA1-2420-2 -55 to 125 14 Ld CERDIP HA3-2425 PDIP 1 November 19, 2004 Features • Maximum Acquisition Time - 10V Step to 0. 4µ ...
Page 2
Absolute Maximum Ratings Voltage Between V+ and V- Terminals .40V Differential Input Voltage . . . . . . . . ...
Page 3
... To 0.01% 10V Step Hold Step Error ±1mV Hold Mode Settling Time Aperture Time (Note 3) Effective Aperture Delay Time Aperture Uncertainty Drift Current (Note HA1-2420 HA1-2425 HA3-2425, HA4P2425, HA9P2425 POWER SUPPLY CHARACTERISTICS Supply Current (+) Supply Current (-) Power Supply Rejection NOTES: = ± 2kΩ 50pF. V ...
Page 4
Test Circuits and Waveforms -IN INPUT S/H HOLD +IN CONTROL CAP C H S/H CONTROL INPUT FIGURE 1. HOLD STEP ERROR AND DRIFT CURRENT S/H CONTROL OUTPUT ∆t NOTE: Measure the slope of the output during hold, ∆V/∆t, and compute ...
Page 5
Schematic Diagram 106 105 ...
Page 6
... The hold capacitor should have extremely high insulation resistance and low dielectric absorption. Polystyrene (below o 85 C), Teflon, or Parlene types are recommended. For more applications, consult Intersil Application Note AN517, or the factory applications group. R 0.002R F F ...
Page 7
CONTROL GND HOLD CAPACITOR OUT V+ FIGURE 9. GUARD RING LAYOUT (BOTTOM VIEW) Glossary of Terms Acquisition Time The time required following a “sample” command, for the output to reach its final value within ±0.1% or ±0.01%. This is the ...
Page 8
Typical Performance Curves 1000 MIN. SAMPLE TIME DRIFT DURING HOLD o FOR 0.1% ACCURACY (mV/s) 10V SWINGS (µs) 100 UNITY GAIN PHASE MARGIN (DEGREES) 10 1.0 UNITY GAIN BANDWIDTH (MHz) 0.1 SLEW RATE (V/µs) 0.01 10pF 100pF ...
Page 9
Typical Performance Curves S/H (5V/DIV OUT (2V/DIV.) -10V TIME (1µs/DIV) FIGURE 16. ACQUISITION TIME (C S/H (5V/DIV OUT (0.5V/DIV.) -1V TIME (1µs/DIV) FIGURE 18. ACQUISITION TIME (C S/H (5V/DIV OUT (50mV/DIV.) -0.1V TIME (500ns/DIV) ...
Page 10
Die Characteristics DIE DIMENSIONS: 102 mils x 61 mils x 19 mils 2590µm x 1550µm x 483µm METALLIZATION: Type: Al ±2k Å Å Thickness: 16k SUBSTRATE POTENTIAL: V- BACKSIDE FINISH: Gold, Nickel, Silicon, etc. Metallization Mask Layout VOS ...
Page 11
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...
Page 12
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...