MT48LC4M16A2TG7E Micron Technology Inc, MT48LC4M16A2TG7E Datasheet - Page 43
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT48LC4M16A2TG7E
Manufacturer Part Number
MT48LC4M16A2TG7E
Description
Manufacturer
Micron Technology Inc
Type
SDRAMr
Datasheet
1.MT48LC4M16A2TG7E.pdf
(72 pages)
Specifications of MT48LC4M16A2TG7E
Organization
4Mx16
Density
64Mb
Address Bus
14b
Access Time (max)
5.4ns
Maximum Clock Rate
143MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
150mA
Pin Count
54
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Not Compliant
PDF: 09005aef80725c0b/Source: 09005aef806fc13c
64MSDRAM_2.fm - Rev. N 12/08 EN
10. For a READ without auto precharge interrupted by a READ (with or without auto pre-
11. For a READ without auto precharge interrupted by a WRITE (with or without auto pre-
12. For a WRITE without auto precharge interrupted by a READ (with or without auto pre-
13. For a WRITE without auto precharge interrupted by a WRITE (with or without auto pre-
14. For a READ with auto precharge interrupted by a READ (with or without auto precharge),
15. For a READ with auto precharge interrupted by a WRITE (with or without auto precharge),
16. For a WRITE with auto precharge interrupted by a READ (with or without auto precharge),
17. For a WRITE with auto precharge interrupted by a WRITE (with or without auto precharge),
6. All states and sequences not shown are illegal or reserved.
7. READs or WRITEs to bank m listed in the Command (Action) column include READs or
8. Concurrent Auto precharge: Bank n will initiate the auto precharge command when its
9. Burst in bank n continues as initiated.
WRITEs with auto precharge enabled and READs or WRITEs with auto precharge disabled.
burst has been interrupted by bank m’s burst.
charge), the READ to bank m will interrupt the READ on bank n, CL later (Figure 12 on
page 25).
charge), the WRITE to bank m will interrupt the READ on bank n when registered
(Figures 14 and 15 on page 27). DQM should be used one clock prior to the WRITE com-
mand to prevent bus contention.
charge), the READ to bank m will interrupt the WRITE on bank n when registered (Figure 22
on page 32), with the data-out appearing CL later. The last valid WRITE to bank n will be
data-in registered one clock prior to the READ to bank m.
charge), the WRITE to bank m will interrupt the WRITE on bank n when registered
(Figure 20 on page 31). The last valid WRITE to bank n will be data-in registered one clock
prior to the READ to bank m.
the READ to bank m will interrupt the READ on bank n, CL later. The precharge to bank n
will begin when the READ to bank m is registered (Figure 29 on page 37).
the WRITE to bank m will interrupt the READ on bank n when registered. DQM should be
used two clocks prior to the WRITE command to prevent bus contention. The precharge to
bank n will begin when the WRITE to bank m is registered (Figure 30 on page 38).
the READ to bank m will interrupt the WRITE on bank n when registered, with the data-out
appearing CL later. The precharge to bank n will begin after
when the READ to bank m is registered. The last valid WRITE to bank n will be data-in regis-
tered one clock prior to the READ to bank m (Figure 31 on page 38).
the WRITE to bank m will interrupt the WRITE on bank n when registered. The precharge to
bank n will begin after
tered. The last valid WRITE to bank n will be data registered one clock prior to the WRITE to
bank m (Figure 32 on page 39).
t
WR is met, where
43
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
WR begins when the WRITE to bank m is regis-
64Mb: x4, x8, x16 SDRAM
t
WR is met, where
©2000 Micron Technology, Inc. All rights reserved.
Commands
t
WR begins