57C43C-35J STMicroelectronics, 57C43C-35J Datasheet
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
57C43C-35J
Specifications of 57C43C-35J
Related parts for 57C43C-35J
57C43C-35J Summary of contents
Page 1
... Bipolar counterparts. A further advantage of the WS57C43C over Bipolar PROM devices is the fact that it utilizes a proven EPROM technology. This enables the entire memory array to be tested for switching characteristics and functionality after assembly. Unlike devices which cannot be erased, every WS5743C in a windowed package is 100% tested with worst case test patterns both before and after assembly ...
Page 2
... WS57C43C ABSOLUTE MAXIMUM RATINGS* Storage Temperature............................–65° 150°C Voltage on any Pin with Respect to Ground ....................................–0.6V to +7V V with Respect to Ground...................–0. 14V PP ESD Protection .................................................. * NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of ...
Page 3
... Address to Output Delay t ACC CS1 to Output Delay t CS Output Disable Output Float Address to Output Hold Sampled, Not 100% Tested. AC READ TIMING DIAGRAM ADDRESSES CS OUTPUTS Over Operating Range. (See Above) 57C43C-25 57C43C-35 57C43C-45 57C43C-55 57C43C-70 MIN MAX MIN MAX MIN MAX VALID t ACC t CS ...
Page 4
... WS57C43C CAPACITANCE ( 25° MHz A SYMBOL PARAMETER C Input Capacitance IN C Output Capacitance OUT C V Capacitance VPP PP NOTES: 4. This parameter is only sampled and is not 100% tested. 5.Typical values are for T = 25°C and nominal supply voltages. A TEST LOAD (High Impedance Test Systems ...
Page 5
... NORMALIZED SUPPLY CURRENT 1.2 1.1 1.0 0.9 0.8 -55 -35 -15 85 105 125 WS57C43C vs. OUTPUT LOADING 200 400 600 800 1000 CAPACITANCE ( pF ) vs. AMBIENT TEMPERATURE 105 125 AMBIENT TEMPERATURE (°C) 2-35 ...
Page 6
... WS57C43C PROGRAMMING INFORMATION DC CHARACTERISTICS SYMBOLS Input Leakage Current Supply Current During Programming Pulse I V Supply Current CC CC Output Low Voltage During Verify mA) OL Output High Voltage During Verify –4 mA) OH NOTES must not be greater than 13 volts including overshoot CHARACTERISTICS SYMBOLS t Address Setup Time ...
Page 7
... ORDERING INFORMATION SPEED PART NUMBER (ns) WS57C43C-25D 25 WS57C43C-25J 25 WS57C43C-25S 25 WS57C43C-25T 25 * WS57C43C-35CMB 35 WS57C43C-35D 35 WS57C43C-35J 35 WS57C43C-35JI 35 WS57C43C-35S 35 WS57C43C-35T 35 * WS57C43C-35TMB 35 WS57C43C-45D 45 WS57C43C-45J 45 WS57C43C-45JI 45 WS57C43C-45S 45 WS57C43C-45T 45 WS57C43C-45TI 45 * WS57C43C-45TMB 45 WS57C43C-55D 55 WS57C43C-55T 55 * WS57C43C-55TMB 55 WS57C43C-70D 70 NOTE: The actual part marking will not include the initials "WS." * SMD product. See section 4 for DESC SMD numbers. ...