LTC2915HTS81#PBF Linear Technology, LTC2915HTS81#PBF Datasheet - Page 7

• Manufacturer Part Number: LTC2915HTS81#PBF
• Manufacturer: Linear Technology

Specifications of LTC2915HTS81#PBF

• Operating Supply Voltage (min): 1.5V
• Operating Supply Voltage (max): 5.5V
• Package Type: TSOT-23
• Operating Temperature Classification: Automotive
• Operating Temp Range: -40C to 125C
• Pin Count: 8
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Compliant

APPLICATIONS INFORMATION
Supply Monitoring
The LTC2915/LTC2916 are low voltage single supply
monitors with selectable thresholds. Two three-state inputs
select one of nine internally programmed thresholds. For
the LTC2915, a third three-state input selects the tolerance
at which the supply connected to the VM pin is monitored
(–5%, –10%, –15%). The tolerance for the LTC2916 is
fi xed at –5%. Threshold accuracy is guaranteed at ±1.5%
over the entire operating temperature range.
The LTC2915/LTC2916 asserts the RST output low when
VM is below the programmed threshold, and for a reset
timeout (t
timeout can be confi gured to use an internal timer with no
external components, or an adjusted timer programmed
by placing an external capacitor from RT to ground.
Power-Up
V
as soon as V
output asserts low.
Until V
(guaranteed less than 1.5V), RST is held low regardless
of the state of VM.
Once V
and VM is above the programmed threshold, the reset
timer is started. After the reset timeout (t
drain pull-down releases RST and the external pull-up
resistor pulls high.
Power-Down
On power-down, once VM drops below its threshold or
V
logic low.
Monitor Threshold Control
The monitor threshold on the VM pin is controlled by
the SEL1, SEL2 and TOL three-state pins. The SEL1 and
SEL2 pins select one of nine preset nominal voltages
(including one externally adjustable threshold) as shown
in Table 1.
CC
CC
powers the drive circuits for the RST pin. Therefore,
drops below the undervoltage lockout, RST asserts
CC
CC
RST
is above the under voltage lockout threshold
reaches the undervoltage lockout threshold
) after VM goes above the threshold. The reset
CC
reaches 0.8V during power up, the RST
RST
), the open
Table 1. Voltage Threshold Settings
*Require a separate supply for V
Table 2. System Voltage Tolerance Settings
The SEL1 and SEL2 three-state input pins should be con-
nected to GND, V
operation. Note that when left unconnected, the maximum
leakage allowable from the pin to either GND or V
±5μA.
The tolerance at which the monitored supply is measured
is set by the TOL pin (LTC2915 only), as shown in Table 2.
If desired (e.g. for margining purposes), the TOL pin may
be driven by a three-state buffer. That three-state buffer
must have a V
the TOL pin specifi ed in the Electrical Characteristics, and
maintain less than 5μA of leakage in the open state.
Threshold Accuracy
The trip threshold for VM is selected by confi guring the
three-state input pins. When using the adjustable input, an
external resistive divider sets the trip threshold, allowing
the user complete control over the trip point. Selection of
this trip voltage is crucial to the reliability of the system.
NOMINAL VOLTAGE
ADJ* (0.5V)
1.5V*
1.2V*
3.3V
2.5V
1.8V
12V
1V*
5V
TOLERANCE
–10%
–15%
–5%
OL
and V
CC
LTC2915/LTC2916
or left unconnected during normal
OH
CC
SEL1
Open
Open
Open
which meet the V
GND
GND
GND
V
V
V
CC
CC
CC
Open
GND
TOL
V
CC
IL
SEL2
Open
Open
Open
GND
GND
GND
V
V
V
and V
CC
CC
CC
CC
29156fa
IH
7
of
is