TL-LP50 Omron, TL-LP50 Datasheet
TL-LP50
Specifications of TL-LP50
Available stocks
Related parts for TL-LP50
TL-LP50 Summary of contents
Page 1
... Approx. 1.4 kg Case Die-cast aluminum Materi- als Sensing surface Polyester Accessories Instruction sheet * Full-wave rectified power supplies with a mean output of 24 VDC ±10% are available for the TL-LP50. http://www.ia.omron.com/ Output configuration 3-wire DC (normally open) 2-wire AC (normally open TL-LP50 --- 2 10 times each and Z directions (c)Copyright OMRON Corporation 2008 All Rights Reserved ...
Page 2
... TL-LY50 at 200 VAC 250 200 Operate ON 150 V mA 200 VAC 100 Reset OFF 100 500 Load current (mA) Column-type Sensing Object Diameter and Material vs. Sensing Distance TL-LP/- Reset Iron Operate 40 l > 120 D dia Reset Brass Operate 120 140 External diameter D dia. (mm) (c)Copyright OMRON Corporation 2008 All Rights Reserved ...
Page 3
... R5 18.5 75 *1. Vinyl cabtire cable: TL-LP50: 9.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.75 mm TL-LY50: 9.0-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.75 mm *2. Remove the hexagon nut if a PF1/2 cable protective tube is applied. (c)Copyright OMRON Corporation 2008 All Rights Reserved. ...
Page 4
... Be sure that the power supply polarity and oth- er wiring is correct. Incorrect wiring may cause explosion or burning. Connection without a Load If the power supply is connected directly with- out a load, the internal elements may explode or burn. Be sure to insert a load when connect- ing the power supply. ...
Page 5
... Conduits, ducts, pre-wired, terminal wiring, ease of main- tenance and inspection mT* max. Do not use the Sensor at a level higher than 20 mT. Life: Power-ON time/frequency of use (c)Copyright OMRON Corporation 2008 All Rights Reserved. Peripheral metal Sensing distance Material, distance Fluctuation in transit point, al- to Sensor, orien- lowable error, etc ...
Page 6
... Sensing Object Material The sensing distance varies greatly depending on the material of the sensing object. Study the engineering data for the influence of sensing object material and size and select a distance with sufficient leeway. • In general, if the Example: E2-X10D@ sensing object is a non- ...
Page 7
... OFF It is recommend that leeway be included in the actual values used. For 12 VDC, use 15 kΩ or less and 450 mW or higher, and for 24 VDC, use 30 kΩ or less and 0 higher. (c)Copyright OMRON Corporation 2008 All Rights Reserved. AC power supply voltage Vs 2 (mW) ...
Page 8
... Loads with Large Inrush Current Loads, such as lamps or motors, that cause a large inrush weaken or damage the switching element. In this situation, use a relay. * E2K, TL-N@ higher ●Mounting Mounting the Sensor When mounting a Sensor, do not tap it with a hammer or otherwise subject it to excessive shock. This will weaken water resistance and may damage the Sensor ...
Page 9
... A parallel connection can be used if A and B will not be operated simulta- neously and there is no need to hold the load. The leakage current, however, Load will be n times the value for each Sensor and reset failures will frequently oc- cur. ("n" is the number of Proximity Sensors and B will be operated simultaneously and the load is held, a parallel con- nection is not possible ...
Page 10
... The residual voltage of the E2E-XD-M1J 3-Wire Sensors Operation can be reversed with the signal input switch on the S3D2. (c)Copyright OMRON Corporation 2008 All Rights Reserved. Description Example: A maximum of two Sensors can be used when an MY (24-VDC) Relay is used for the load ...
Page 11
... Disassembly and Repair Do not under any circumstances attempt to disassemble or repair the product. Quick Failure Check You can conveniently check for failures by connecting the E39-VA Handy Checker to check the operation of the Sensor. http://www.ia.omron.com/ Proximity Sensors Technical Guide (c)Copyright OMRON Corporation 2008 All Rights Reserved. ...
Page 12
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specifi ed) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...