CAT5118SDI-10 ON Semiconductor, CAT5118SDI-10 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CAT5118SDI-10
Manufacturer Part Number
CAT5118SDI-10
Description
Manufacturer
ON Semiconductor
Datasheet
1.CAT5118SDI-10.pdf
(15 pages)
Specifications of CAT5118SDI-10
Number Of Elements
1
# Of Taps
32
Resistance (max)
10KOhm
Power Supply Requirement
Single
Interface Type
Serial (2-Wire)
Single Supply Voltage (typ)
3.3/5V
Dual Supply Voltage (typ)
Not RequiredV
Single Supply Voltage (min)
2.7V
Single Supply Voltage (max)
5.5V
Dual Supply Voltage (min)
Not RequiredV
Dual Supply Voltage (max)
Not RequiredV
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
5
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CAT5118SDI-10-T
Manufacturer:
CATALYST
Quantity:
20 000
FUNCTIONAL DESCRIPTION
The CAT5110/5118/5119/5123/5124/5125 consist of a
fixed resistor and a wiper contact with 32-tap points
that are digitally controlled through a 2-wire up/down
serial interface. Three end-to-end resistance values
are available: 10kΩ, 50kΩ and 100kΩ.
The CAT5110/5125 is designed to operate as a
potentiometer. In this configuration, the low terminal of
the resistor array is connected to ground (pin 2).
The CAT5118/5123 performs as a variable resistor. In
this device, the wiper terminal and high terminal of the
resistor
CAT5119/5124 is a similar variable resistor, except
the low terminal is connected to pin 5.
Digital Interface Operation
The MiniPots have two modes of operation when the
serial interface is active: increment and decrement
mode. The serial interface is only active when CS
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
CS
U/D
W
Note: "W" is not a digital signal. It represents wiper transitions.
array
CS
U/D
W
Note: "W" is not a digital signal. It represents wiper transitions.
are
t
CU
connected
t
CU
Figure 2. Serial Interface Timing Diagram, Decrement Mode
Figure 1. Serial Interface Timing Diagram, Increment Mode
at
t
CI
pin
t
SETTLE
t
CI
¯¯ is low.
5.
t
CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125
SETTLE
t
The
IL
t
IH
5
The CS
wiper along the resistor array. When CS
from high to low, the part will go into increment mode
if U/D ¯ input is high, and into decrement mode when
U/D ¯ input is low. Once the mode is set, the device will
remain in that mode until CS
to-high transition at the U/D ¯ pin will increment or
decrement the wiper position depending on the
current mode (Figures 1 and 2).
When the CS
inactive), the value of the counter is stored and the
wiper position is maintained.
Note that when the wiper reaches the maximum (or
minimum) tap position, the wiper will not wrap around
to the minimum (or maximum) position.
Power-On Reset
All parts in this family feature power-on reset (POR)
circuitry that sets the wiper position to midscale at
power-up. By default, the chip is in the increment mode.
t
¯¯ and U/D ¯ inputs control the position of the
IH
t
IL
¯¯ input transitions to high (serial interface
t
SETTLE
¯¯ goes high again. A low-
t
IC
t
SETTLE
Doc. No. MD-2120 Rev. L
t
IC
¯¯ transitions