PVT422P-TPBF International Rectifier, PVT422P-TPBF Datasheet

84K9023

PVT422P-TPBF

Manufacturer Part Number
PVT422P-TPBF
Description
84K9023
Manufacturer
International Rectifier
Datasheet

Specifications of PVT422P-TPBF

Input Type
DC
Output Voltage (max)
400V
Input Current (max)
25mA
Isolation Voltage
3.75kV
Circuit Arrangement
2 Form A
Package Type
Thin-PAK
Output Device
MOSFET
Pin Count
8
Mounting
Surface Mount
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Rad Hardened
No
Output Type
AC/DC
Load Voltage Max
400V
Load Current
120mA
On State Resistance Max
35ohm
Contact Configuration
DPNO
Forward Current If
5mA
Relay Terminals
SMD
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Compliant
www.irf.com
General Description
The PVT422P Series Photovoltaic Relay is a dual-pole,
normally open solid-state relay that can replace
electromechanical relays in many applications. It
utilizes International Rectifier’s HEXFET power
MOSFET as the output switch, driven by an integrated
circuit photovoltaic generator of novel construction.
The output switch is controlled by radiation from a
GaAlAs light emitting diode (LED) which is optically
isolated from the photovoltaic generator.
PVT422P is ideally suited for PCMCIA card applica-
tions. Its extremely low profile allows it to be used in
Type II cards whose outer shells are only 5mm thick.
Series PVT422P Relays are packaged in an 8-pin,
molded ‘Thin-Pak’ DIP package with ‘gull-wing’ sur-
face mount terminals. It is available in plastic ship-
ping tubes or on tape-and-reel. Please refer to Part
Identification (opposite) for details.
Applications
!
!
!
!
General switching
On/Off Hook switch
Dial-Out relay
Ring injection relay
(HEXFET is the registered trademark for International Rectifier Power MOSFETs)
OBSOLETE
HEXFET
Features
Part Identification
PVT422P surface-mount, plastic shipping
tube
PVT422P-T surface-mount, tape-and-reel
!
!
!
!
!
!
!
®
Power MOSFET Photovoltaic Relay
HEXFET Power MOSFET output
Bounce-free operation
3,750 V
Load current limiting
Linear AC/DC operation
Solid-State Reliability
BABT certified
PVT422P - Thin-Pak
Data Sheet No. PD 10043 revE
RMS
Dual Pole, Normally Open
Microelectronic Power IC
I/O isolation
0-400V, 120mA AC/DC
PVT422P
1

Related parts for PVT422P-TPBF

PVT422P-TPBF Summary of contents

Page 1

... General Description The PVT422P Series Photovoltaic Relay is a dual-pole, normally open solid-state relay that can replace electromechanical relays in many applications. It utilizes International Rectifier’s HEXFET power MOSFET as the output switch, driven by an integrated circuit photovoltaic generator of novel construction. The output switch is controlled by radiation from a GaAlAs light emitting diode (LED) which is optically isolated from the photovoltaic generator ...

Page 2

... Series PVT422P Electrical Specifications (-40°C T INPUT CHARACTERISTICS Minimum Control Current (See figure1) Maximum Control Current for Off-State Resistance @TA=+25°C Control Current Range (Caution: current limit input LED, see figure 5) Maximum Reverse Voltage OUTPUT CHARACTERISTICS Operating Voltage Range Maximum Load Current @ T =+40° ...

Page 3

... Figure 1. Typical Current Derating Curve Figure 3. Typical Normalized On-Resistance Figure 5. Input Characteristics (Current Controlled) www.irf.com NOT recommended for new designs Figure 2. Linearity Characteristics Figure 4. Typical Normalized Off-State Leakage Figure 6. Typical Delay Times Series PVT422P 3 ...

Page 4

... Series PVT422P Figure 7. Delay Time Definitions Case Outline IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 4 NOT recommended for new designs Figure 8. Typical Output Capacitance Data and specifications subject to change without notice. 2/2/2007 01-2011 00 www.irf.com ...

Related keywords