LFXP15C-4FN256C LATTICE SEMICONDUCTOR, LFXP15C-4FN256C Datasheet - Page 17
LFXP15C-4FN256C
Manufacturer Part Number
LFXP15C-4FN256C
Description
FPGA LatticeXP Family 15000 Cells 360MHz 130nm (CMOS) Technology 1.8V/2.5V/3.3V 256-Pin FBGA Tray
Manufacturer
LATTICE SEMICONDUCTOR
Datasheet
1.LFXP3C-3QN208C.pdf
(130 pages)
Specifications of LFXP15C-4FN256C
Package
256FBGA
Family Name
LatticeXP
Device Logic Units
15000
Maximum Internal Frequency
360 MHz
Typical Operating Supply Voltage
1.8|2.5|3.3 V
Maximum Number Of User I/os
188
Ram Bits
331776
Re-programmability Support
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LFXP15C-4FN256C
Manufacturer:
CY
Quantity:
105
Company:
Part Number:
LFXP15C-4FN256C
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
- Current page: 17 of 130
- Download datasheet (2Mb)
Lattice Semiconductor
Figure 2-15. Memory Core Reset
For further information on sysMEM EBR block, see the details of additional technical documentation at the end of
this data sheet.
EBR Asynchronous Reset
EBR asynchronous reset or GSR (if used) can only be applied if all clock enables are low for a clock cycle before the
reset is applied and released a clock cycle after the reset is released, as shown in Figure 2-16. The GSR input to the
EBR is always asynchronous.
Figure 2-16. EBR Asynchronous Reset (Including GSR) Timing Diagram
If all clock enables remain enabled, the EBR asynchronous reset or GSR may only be applied and released after
the EBR read and write clock inputs are in a steady state condition for a minimum of 1/f
release must adhere to the EBR synchronous reset setup time before the next active read or write clock edge.
If an EBR is pre-loaded during configuration, the GSR input must be disabled or the release of the GSR during
device Wake Up must occur before the release of the device I/Os becoming active.
These instructions apply to all EBR RAM and ROM implementations.
Note that there are no reset restrictions if the EBR synchronous reset is used and the EBR GSR input is disabled.
Programmable I/O Cells (PICs)
Each PIC contains two PIOs connected to their respective sysIO Buffers which are then connected to the PADs as
shown in Figure 2-17. The PIO Block supplies the output data (DO) and the Tri-state control signal (TO) to sysIO
buffer, and receives input from the buffer.
GSRN
RSTA
RSTB
Programmable Disable
Reset
Clock
Clock
Enable
Memory Core
2-14
Output Data
L
L
D
D
Latches
CLR
CLR
SET
SET
Q
Q
LatticeXP Family Data Sheet
Port A[17:0]
Port B[17:0]
MAX
(EBR clock). The reset
Architecture
Related parts for LFXP15C-4FN256C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FPGA LatticeXP Family 15000 Cells 320MHz 130nm (CMOS) Technology 1.8V/2.5V/3.3V 256-Pin FBGA Tray
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
Part Number:
Description:
FPGA LatticeXP Family 15000 Cells 320MHz 130nm (CMOS) Technology 1.8V/2.5V/3.3V 256-Pin FBGA Tray
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
Part Number:
Description:
FPGA LatticeXP Family 15000 Cells 320MHz 130nm (CMOS) Technology 1.8V/2.5V/3.3V 388-Pin FBGA Tray
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
Part Number:
Description:
LatticeXP Family
Manufacturer:
Lattice Semiconductor
Datasheet:
Part Number:
Description:
ISPLSI2032-80LT44Lattice Semiconductor [In-System Programmable High Density PLD]
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
IC PROGRAMMED LATTICE GAL 16V8
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet: