H7ET-N Omron, H7ET-N Datasheet - Page 10
![TIME COUNTER LCD NO-VOLT IN BG](/photos/6/44/64471/h7et-n_sml.jpg)
H7ET-N
Manufacturer Part Number
H7ET-N
Description
TIME COUNTER LCD NO-VOLT IN BG
Manufacturer
Omron
Series
H7ETr
Specifications of H7ET-N
Operating Mode
Accumulative
Output Type
None
Voltage - Supply
None Required (Battery Included)
Termination Style
Screw Terminal
Display Type
LCD Non-Backlit
Number Of Digits/alpha
7
No. Of Digits / Alpha
7
Digit Height
8.6mm
Operating Temperature Range
-10°C To +55°C
Svhc
No SVHC (15-Dec-2010)
External Depth
48.5mm
External Length / Height
24mm
External Width
48mm
Operating Temperature Max
55°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Input Type
-
Count Rate
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
H7ET-N
H7ETN
H7ETNQ
Z3003
H7ETN
H7ETNQ
Z3003
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
H7ET-N
Manufacturer:
Omron Electronics Inc-IA Div
Quantity:
135
Company:
Part Number:
H7ET-NFV1-B
Manufacturer:
Omron Electronics Inc-IA Div
Quantity:
135
Company:
Part Number:
H7ET-NV1
Manufacturer:
Omron Electronics Inc-IA Div
Quantity:
135
New H7E
Count/Timer Input or Reset Input to More than
One H7E Counter at a Time
Note: H (Reset ON) level must be 4.5 V minimum.
Note: 1. The leakage current of the transistor used for input must
Input and Power Supply
No-voltage Input Models
32
PNP/NPN Universal DC Voltage Input
No-voltage Input
Do not impose voltage on the Counter if the Counter is a model
that operates with no-voltage input, otherwise the internal circuit
of the Counter may be damaged.
Do not connect any single input signal in parallel to Counter
models operating with no-voltage input and those operating with
voltage input, otherwise the Counters may malfunction.
When connecting a sensor to the Counter that operates with
no-voltage input, make sure that the sensor has open collector
output.
When connecting an open collector input from a transistor to the
Counter that operates with no-voltage input, make sure that the
leakage current of the transistor is 1 A maximum.
H =
2. The forward voltage of the diode must be as low as pos-
be less than 1 A.
sible (i.e., 0.1 V maximum with an I
voltage between terminals 3 and 4 will be 0.5 V when the
reset input is ON.
4.7 (k )/N + V
4.7 (k )/N + R
Sensor
or
or
F
of 20 A) so that the
or
No-voltage Input and PNP/NPN Universal DC Voltage Input
Models
AC/DC Multi-voltage Input Models
Backlight Power Supply
Input Verification with the H7ET Time Counter
(When the time range is not set to 0s to 999h59m59s )
The decimal point of the LCD blinks every other second while an
input signal is being applied. If the decimal point is not blinking, the
input signal is not being received correctly. Check the input signal
connections.
Unit Label for Time Counter and Tachometer
A unit label has been packed with the Counter. Use in accordance
with the application.
Battery Replacement
Remove the wiring when replacing the Battery. Do not come in con-
tact with any item to which high voltage is being applied. Doing so
may result in electric shock.
Before changing the Battery, the person should ensure that they are
not carrying any static electric charge.
Procedure for replacing the Battery (refer to the diagrams below):
1. Using the tool, pry open the lift-tab on the case. (1)
2. Pull the body out of its outer case. (2)
3. Lift the Battery up by the edge and remove it. (3)
The operation of the Counter may be affected if the line voltage of
the power supply exceeds 500 pF (about 10 m, with parallel
wires of 2 x 2 mm).
Keep all wires as short as possible. When using shielded wire,
line capacitance may occur.
When connecting count/timer input from an SSR to the Counter
that operates with AC/DC voltage input, use OMRON’s
G3TA-IA/ID SSR (for DC) whose leakage current is 0.1 mA max.
or connect a bleeder resistor in parallel to the input circuit of the
Counter.
To reduce variation in the brightness of the backlight when using
more than one H7E with a backlight, use the same power supply
for all the backlights.
When connecting the DC power supply for the backlights, be
sure to connect the polarities correctly.
When removing the Battery, do not come in contact with the
display area or any internal parts.
or
or
*Bleeder resistor
The voltage between terminals 1 and 2 must be
1.5 V maximum when the SSR is OFF.
Leakage current:
0.1 mA max.
or
New H7E