LC4H-T4-DC24VS Panasonic Electric Works, LC4H-T4-DC24VS Datasheet - Page 14

• Manufacturer Part Number: LC4H-T4-DC24VS
• Description: COUNTER DIGITAL 24VDC SCREW TERM
• Manufacturer: Panasonic Electric Works
• Series: LC4Hr

Specifications of LC4H-T4-DC24VS

• Count Rate: 30Hz or 5kHz Selectable
• Number Of Digits/alpha: 4
• Input Type: Switch Closure or Transistor Switch
• Output Type: Transistor
• Voltage - Supply: 12 V ~ 24 V
• Display Type: LCD Backlit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LC4HT4DC24VS; Q1150188

Setting the operation mode and counter
Setting procedure 1) Setting the operation mode (input mode and output mode)
Setting procedure 2) Setting the set value
Setting procedure 3) Setting the input mode
Set the set value with the UP and DOWN keys on the front of the counter.
Front display section
• 4-digit display type
Q Counter display
W Set value display
E Controlled output indicator
R Reset indicator
T Lock indicator
Y UP keys
• 6-digit display type
Q Counter display
W Set value display
E Controlled output indicator
R Reset indicator
T Lock indicator
The input mode is set using the key switch in the [Display] section on the front of the counter.
• Decimal point position setting mode
Q Holding down the [SET/LOCK] key, press the key for the second digit to access the decimal point position setting mode.
W When the setting mode has been accessed, release the [SET/LOCK] key.
Changes the corresponding
digit of the set value in the
addition direction (upwards)
Set the input and output modes with the DIP switches on the side of the counter.
DIP switches
1
2
3
4
5
6
7
8
Minimum reset input signal width
Maximum counter setting
(Same for 6-digit, screw-down terminal type)
Output mode
Input mode
1
Item
2
3
4
5
6
7
8
Example) 6-digit type
Decimal point position setting mode display
(Example shows default value displayed)
DIP switches (See note 2)
3
4
5
8
9
3
4
5
7
8
20 ms
30 Hz
OFF
Refer to table 1
Refer to table 2
DIP switch
SET/LOCK
LC4H
SET/LOCK
RESET
RESET
OP.
RST
LOCK
OP.
RST
LOCK
5 kHz
1 ms
ON
DOWN
UP
COUNTER
COUNTER
LC4H
Table 1: Setting the output mode
Table 2: Setting the input mode
Notes:1) The counter and set value displays will display DIP Err.
Notes:2) Set the DIP switches before installing the counter on the panel.
Notes:3) When the DIP SW setting is changed, turn off the power once.
Notes:4) The DIP switches are set as ON before shipping.
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
1
6
1
2
6
7
1
2
6
DIP switch No.
DIP switch No.
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
2
7
U DOWN keys
I RESET switch
O SET/LOCK switch
Y UP keys
U RESET switch
I SET/LOCK switch
Changes the corresponding digit of the set
value in the subtraction direction (down-
wards)
Resets the counting value and the output
This is used to handle pre-scaling values,
one-shot times, decimal point position set-
tings, and key lock operations (to disable Up
key, Down key, and Reset key operations).
Changes the corresponding digit of the set
value in the addition direction (upwards)
Resets the counting value and the output
This is used to handle pre-scaling values,
one-shot times, decimal point position set-
tings, and key lock operations (to disable Up
key, Down key, and Reset key operations).
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
3
8
SHOT-A
SHOT-B
SHOT-C
SHOT-D
HOLD-A
HOLD-B
HOLD-C
—
Addition input
Subtraction input
Directive input
Independent input
Phase input
—
—
—
(See note 1)
(See note 1)
(See note 1)
(See note 1)
Output mode
Input mode
LC4H-S
127