LD200600 Red Lion Controls, LD200600 Datasheet - Page 3

LD200600

Manufacturer Part Number

LD200600

Description

COUNTER 6 DIGIT 2.25" 120VAC RED

Manufacturer

Red Lion Controls

Series

LDr

Datasheet

1.LD200400.pdf (16 pages)

Specifications of LD200600

Count Rate

35kHz

Number Of Digits/alpha

Input Type

Voltage, Switch Closure, Transistor Switch

Voltage - Supply

11 V ~ 16 VDC, 85 V ~ 250 VAC

Display Type

LED Red

No. Of Digits / Alpha

Digit Height

57mm

Power Consumption

26VA

Counting Speed

25kHz

Operating Temperature Range

0Â°C To +50Â°C

Signal Input Type

Pulse

Character Size

2.25"

Ip/nema Rating

IP65 / NEMA 4X

Counter Supply Voltage

85-250VAC/11-16VDC

Rohs Compliant

Yes

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Output Type

Lead Free Status / RoHS Status

Lead free / RoHS Compliant, Lead free / RoHS Compliant

Current page: 3 of 16
Download datasheet (2Mb)

EMC INSTALLATION GUIDELINES

Magnetic Interference (EMI), proper installation and wiring methods must be

followed to ensure compatibility in each application. The type of the electrical

noise, source or coupling method into the meter may be different for various

installations. The meter becomes more immune to EMI with fewer I/O

connections. Cable length, routing, and shield termination are very important

and can mean the difference between a successful or troublesome installation.

Listed below are some EMC guidelines for successful installation in an

industrial environment.

1. The meter should be properly connected to protective earth.

2. Use shielded (screened) cables for all Signal and Control inputs. The shield

3. Never run Signal or Control cables in the same conduit or raceway with AC

SETTING THE 8 DIP SWITCHES

eight switches is located inside the unit.

SWITCH 1 (Input A)

SWITCH 2 (Input A) {See Note 1}

SWITCH 3 (Input A)

SWITCH 4 (Input B) {See Note 1}

SWITCH 5 (Input B)

2.0 S

3.0 W

Although this meter is designed with a high degree of immunity to Electro-

(screen) pigtail connection should be made as short as possible. The

connection point for the shield depends somewhat upon the application.

Listed below are the recommended methods of connecting the shield, in order

of their effectiveness.

a. Connect the shield only at the panel where the unit is mounted to earth

b. Connect the shield to earth ground at both ends of the cable, usually when

c. Connect the shield to common of the meter and leave the other end of the

power lines, conductors feeding motors, solenoids, SCR controls, and

heaters, etc. The cables should be ran in metal conduit that is properly

grounded. This is especially useful in applications where cable runs are long

and portable two-way radios are used in close proximity or if the installation

is near a commercial radio transmitter.

To access the switches, remove the right side plate of the meter. A bank of

LOGIC: Input A trigger levels V

MAG: 200 mV peak input sensitivity; 100 mV hysteresis; maximum voltage:

SNK.: Adds internal 7.8 K pull-up resistor to +12 VDC, I

SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.

HI Frequency: Removes damping capacitor and allows max. frequency.

LO Frequency: Adds a damping capacitor for switch contact bounce. Limits

SNK.: Adds internal 7.8 K pull-up resistor to +12 VDC, I

SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.

HI Frequency: Removes damping capacitor and allows max. frequency.

LO Frequency: Adds a damping capacitor for switch contact bounce. Limits

ground (protective earth).

the noise source frequency is above 1 MHz.

shield unconnected and insulated from earth ground.

40 V peak (28 Vrms); Must also have SRC switch ON. (Not recommended

with counting applications.)

input frequency to 50 Hz and input pulse widths to 10 msec.

MAX

Warning: Exposed line voltage exists on the circuit boards.

Remove all power to the meter and load circuits before accessing

inside of the meter.

= 28 VDC

ETTING THE

IRING THE

= 1.25 V max.; V

DIP S

MAX

= 2.75 V min.;

ETER

= 2.1 mA.

WITCHES

SWITCH 6 (RESET/USER INPUT) {See Note 1}

SWITCH 7 (POWER UP RESET)

Note: This switch has no function for programmable models. Power-up reset is

SWITCH 8 (Input B)

Note 1: When the DIP switch is in the SNK position (OFF), the input is

4. Signal or Control cables within an enclosure should be routed as far as possible

5. In extremely high EMI environments, the use of external EMI suppression

6. Long cable runs are more susceptible to EMI pickup than short cable runs.

7. Switching of inductive loads produces high EMI. Use of snubbers across

SNK.: Adds internal 7.8 K pull-up resistor to +12VDC, I

SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.

ENABLE: In this position, the counter resets to zero at power up.

DISABLE: In this position, the counter does not reset at power up.

selected through a programming parameter.

DIRECTION CONTROL: In this position Input B is used to control the

INTENSITY ADJUST: In this position Input B is used to adjust the

configured as active low. When the switch is in the SRC position (ON), the

input is configured as active high.

from contactors, control relays, transformers, and other noisy components.

devices, such as ferrite suppression cores, is effective. Install them on Signal

and Control cables as close to the unit as possible. Loop the cable through the

core several times or use multiple cores on each cable for additional protection.

Install line filters on the power input cable to the unit to suppress power line

interference. Install them near the power entry point of the enclosure. The

following EMI suppression devices (or equivalent) are recommended:

Note: Reference manufacturer's instructions when installing a line filter.

Therefore, keep cable runs as short as possible.

inductive loads suppresses EMI.

Snubber: RLC# SNUB0000.

count direction of Input A when Input A is set to Count with Direction

mode (default mode).

LED intensity. There are five distinct LED levels that can be changed by

pulsing Input B. After setting the desired intensity, move switch to

OFF position for Direction Control. Units with keypads can program the

LED intensity level using Programming Menu 3.

Ferrite Suppression Cores for signal and control cables:

Line Filters for input power cables:

Fair-Rite # 0443167251 (RLC# FCOR0000)

TDK # ZCAT3035-1330A

Steward # 28B2029-0A0

Schaffner # FN610-1/07 (RLC# LFIL0000)

Schaffner # FN670-1.8/07

Corcom # 1 VR3

Input B Direction Control

Pwr Up Reset DISABLE

Reset/User Input SNK.

Input A

Input B

HI FREQ.

LOGIC

SNK.

Factory Setting

MAG.

SRC.

LO FREQ.

SRC.

LO FREQ.

SRC.

ENABLE

Intensity Adjust

MAX

= 2.1 mA.