SY87700ALHG Micrel Inc, SY87700ALHG Datasheet

Page 1

... Data sheets and support documentation can be found on Micrel’s web site at: www.micrel.com. AnyRate is a registered trademark of Micrel, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com August 2009 SY87700AL Low-Power, 3.3V, 32Mbps to 208Mbps ® ...

Page 2

... Pb-Free package is recommended for new designs. Pin Configuration 28-Pin SOIC (Z28-1) August 2009 Operating Package Range Marking Industrial SY87700ALZG with Pb-Free bar-line indicator Industrial SY87700ALHG with Pb-Free bar-line indicator = 25°C, DC Electricals only. A 32-Pin EPAD-TQFP (H32-1) 2 SY87700AL Lead Finish NiPdAu Pb-Free NiPdAu ...

Page 3

Micrel, Inc. Pin Description Inputs Pin Number Pin Number (28-SOIC) (32-TQFP FREQSEL1 8 6 FREQSEL2 9 7 FREQSEL3 Outputs ...

Page 4

Micrel, Inc. Power and Ground Pin Number Pin Number (28-SOIC) (32-TQFP 29, 30 20, 23 19, 22 13 Note: 1. VCC, VCCA, VCCO must be the same value. August ...

Page 5

Micrel, Inc. Absolute Maximum Ratings Supply Voltage (V ) ................................... -0.5V to +4.0V CC Input Voltage (V ) ........................................... -0. Output Current (I ) OUT Continuous........................................................ ±50mA Surge .............................................................. ±100mA Lead Temperature (soldering, 20sec.) ................... +260°C Storage ...

Page 6

Micrel, Inc. AC Electrical Characteristics 3.3V ±5 CCO CCA Symbol Parameter f VCO Center Frequency VCO Δf VCO Center Frequency VCO Tolerance t Acquisition Lock Time ACQ t REFCLK Pulse Width HIGH ...

Page 7

Micrel, Inc. Functional Block Functional Description Clock Recovery Clock recovery, as shown in the block diagram, generates a clock that is at the same frequency as the incoming data bit rate at the serial data input. The clock is phase ...

Page 8

Micrel, Inc. . Frequency Selection Table FREQSEL1 FREQSEL2 Notes: 1. SY87700AL operates from 32MHz to 208MHz. For higher speed applications, the SY87701AL operates from 28MHz to 1300MHz DON’T CARE. ...

Page 9

Micrel, Inc. Application Example AC-Coupled I/O August 2009 9 hbwhelp@micrel.com SY87700AL M9999-082009-D or (408) 955-1690 ...

Page 10

Micrel, Inc. Application Example DC-Coupled I/O Related Product and Support Documentation Part Number Function SY87701AL Low-Power 3.3V, 28Mbps to 1300Mbps ® AnyRate Clock and Data Recovery HBW Solutions New Products and Applications August 2009 Data Sheet Link www.micrel.com/product-info/products/sy87701al.shtml www.micrel.com/product-info/products/solutions.shtml 10 ...

Page 11

Micrel, Inc. Bill of Materials (AC-Coupled) Item Part Number C6 293D685X0025B2T C7 VJ206Y103JXJAT C10, C11 VJ0603Y105JXJAT C12-C15, VJ0402Y104JXJAT C18, C19, C27, C28 C20-C26 VJ0402Y104JXJAT D1 P301-ND D2 P300-ND/P301-ND J2, J3, J4, 111-0702-001 J6 J5 BLM21A102F Q1 459-2598-5-ND R1 CRCW04023500F R2 ...

Page 12

Micrel, Inc. Bill of Materials (DC-Coupled) Item Part Number C6 293D685X0025B2T C7 VJ206Y103JXJAT C10, C11 VJ0603Y105JXJAT C12-C15, VJ0402Y104JXJAT C18, C19, C27, C28 C20-C26 VJ0402Y104JXJAT D1 P301-ND D2 P300-ND/P301-ND J2, J3, J4, 111-0702-001 J6 J5 BLM21A102F Q1 459-2598-5-ND R1 CRCW04023500F R2 ...

Page 13

Micrel, Inc. Appendix A Layout and General Suggestions 1. Establish controlled impedance stripline, microstrip, or coplanar construction techniques. 2. Signal paths should have approximately the same width as the device pads. 3. All differential paths are critical timing paths, where ...

Page 14

Micrel, Inc. Package Information Note: 1. The 28-pin SOIC package is NOT recommended for new designs. August 2009 28-Pin SOIC .300” Wide (Z28-1) 14 SY87700AL M9999-082009-D hbwhelp@micrel.com or (408) 955-1690 ...

Page 15

Micrel, Inc. August 2009 32-Pin EPAD-TQFP (H32-1) (Die Up) 15 SY87700AL M9999-082009-D hbwhelp@micrel.com or (408) 955-1690 ...

Page 16

Micrel, Inc. Package Notes: 1. Package meets Leve 2 moisture sensitivity classification and is shipped in dry-pack form. 2. Exposed pad must be soldered to a ground for proper thermal management. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 ...