ICS9179BF-03T IDT, Integrated Device Technology Inc, ICS9179BF-03T Datasheet - Page 4

• Manufacturer Part Number: ICS9179BF-03T
• Description: IC FANOUT BUFFER LOW SKEW 28SSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Fanout Buffer (Distribution)r

Specifications of ICS9179BF-03T

• Number Of Circuits: 1
• Ratio - Input:output: 1:10
• Differential - Input:output: No/No
• Input: Clock
• Output: Clock
• Frequency - Max: 133MHz
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• Frequency-max: 133MHz
• Number Of Outputs: 10
• Operating Supply Voltage (max): 3.465V
• Operating Temp Range: 0C to 70C
• Propagation Delay Time: 8ns
• Operating Supply Voltage (min): 3.135V
• Mounting: Surface Mount
• Pin Count: 28
• Operating Supply Voltage (typ): 3.3V
• Package Type: SSOP
• Input Frequency: 133MHz
• Duty Cycle: 55%
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 9179BF-03T

0258K 12/15/08
How to Write:
• Controller (host) sends a start bit.
• Controller (host) sends the write address D2
• ICS clock will acknowledge
• Controller (host) sends a dummy command code
• ICS clock will acknowledge
• Controller (host) sends a dummy byte count
• ICS clock will acknowledge
• Controller (host) starts sending first byte (Byte 0)
• ICS clock will acknowledge each byte one at a time.
Notes:
1.
2.
3.
4.
5.
6.
ICS9179-03
through byte 5
The ICS clock generator is a slave/receiver, I
verification. Read-Back will support Intel PIIX4 "Block-Read" protocol.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
The input is operating at 3.3V logic levels.
The data byte format is 8 bit bytes.
To simplify the clock generator I
bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete
byte has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored
for those two bytes. The data is loaded until a Stop sequence is issued.
At power-on, all registers are set to a default condition, as shown.
Dummy Command Code
Dummy Byte Count
Controller (Host)
Address
Start Bit
Stop Bit
Byte 0
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
Byte 6
D2
(H)
How to Write:
The information in this section assumes familiarity with I
General I
ICS (Slave/Receiver)
ACK
ACK
ACK
ACK
ACK
ACK
ACK
ACK
ACK
ACK
2
C interface, the protocol is set to use only "Block-Writes" from the controller. The
2
C serial interface information
(H)
2
C component. It can read back the data stored in the latches for
4
How to Read:
• Controller (host) will send start bit.
• Controler (host) sends the read address D3
• ICS clock will acknowledge
• ICS clock will send the byte count
• Controller (host) acknowledges
• ICS clock sends first byte (Byte 0) through byte 6
• Controller (host) will need to acknowledge each byte
• Controller (host) will send a stop bit
Controller (Host)
2
Address
C programming.
Start Bit
Stop Bit
D3
ACK
ACK
ACK
ACK
ACK
ACK
ACK
ACK
(H)
How to Read:
ICS (Slave/Receiver)
Byte Count
Byte 0
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
Byte 6
ACK
(H)