FS7145-02G-XTD ON Semiconductor, FS7145-02G-XTD Datasheet - Page 4

• Manufacturer Part Number: FS7145-02G-XTD
• Description: IC CLOCK GEN PLL PROG 16SSOP
• Manufacturer: ON Semiconductor
• Type: Clock/Frequency Synthesizerr

Specifications of FS7145-02G-XTD

• Pll: Yes
• Input: Crystal
• Output: CMOS, PECL
• Number Of Circuits: 1
• Ratio - Input:output: 2:1
• Differential - Input:output: No/Yes
• Frequency - Max: 300MHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 16-SSOP
• Frequency-max: *
• Number Of Elements: 1
• Pll Input Freq (max): 80MHz
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Package Type: SSOP
• Output Frequency Range: 0 to 300MHz
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Commercial
• Pin Count: 16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

FS714x
4.1.1. Reference Divider
The reference divider is designed for low phase jitter. The divider accepts the output of either the crystal oscillator circuit or an external
reference frequency. The reference divider is a 12 bit divider, and can be programmed for any modulus from 1 to 4095 (divide by 1 not
available on date codes prior to 0108).
4.1.2. Feedback Divider
The feedback divider is based on a dual-modulus divider (also called dual-modulus prescaler) technique. It permits division by any
integer value between 12 and 16383. Simply program the FBKDIV register with the binary equivalent of the desired modulus. Selected
moduli below 12 are also permitted. Moduli of: 4, 5, 8, 9, and 10 are also allowed (4 and 5 are not available on date codes prior to
0108).
4.1.3. Post Divider
The post divider consists of three individually programmable dividers, as shown in Figure 3.
The moduli of the individual dividers are denoted as N
The post divider performs several useful functions. First, it allows the VCO to be operated in a narrower range of speeds compared to
the variety of output clock speeds that the device is required to generate. Second, the extra integer in the denominator permits more
flexibility in the programming of the loop for many applications where frequencies must be achieved exactly.
Note that a nominal 50/50 duty factor is always preserved (even for selections which have an odd modulus).
See Table 8 for additional information.
4.1.4. Crystal Oscillator
The FS7140 is equipped with a Pierce-type crystal oscillator. The crystal is operated in parallel resonant mode. Internal load
capacitance is provided for the crystal. While a recommended load capacitance for the crystal is specified, crystals for other standard
load capacitances may be used if great precision of the reference frequency (100ppm or less) is not required.
4.1.5. Reference Divider Source MUX
The source of frequency for the reference divider can be chosen to be the device crystal oscillator or the REF pin by the REFDSRC bit.
When not using the crystal oscillator, it is preferred to connect XIN to VSS. Do not connect to XOUT.
Rev. 5 | Page 4 of 19 | www.onsemi.com
P1
N
, N
PX
Figure 3: Post Divider
P2
= N
and N
P1
P3
x N
, and together they make up the array modulus N
P2
x N
P3
PX
.