IDT5V9885NLGI8 IDT, Integrated Device Technology Inc, IDT5V9885NLGI8 Datasheet - Page 24

no-image

IDT5V9885NLGI8

Manufacturer Part Number
IDT5V9885NLGI8
Description
IC CLK GEN 3.3V EEPROM 28-VFQFPN
Manufacturer
IDT, Integrated Device Technology Inc
Type
Clock Generatorr
Datasheet

Specifications of IDT5V9885NLGI8

Pll
Yes with Bypass
Input
LVCMOS, LVTTL, Crystal
Output
LVCMOS, LVDS, LVPECL, LVTTL
Number Of Circuits
1
Ratio - Input:output
2:8
Differential - Input:output
No/Yes
Frequency - Max
500MHz
Divider/multiplier
Yes/Yes
Voltage - Supply
3.135 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-VFQFN, 28-VFQFPN
Frequency-max
500MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
5V9885NLGI8

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
IDT5V9885NLGI8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
NOTE:
PROGWRITE is for writing to the 5v9885 registers.
PROGREAD is for reading the 5v9885 registers.
PROGSAVE is for saving all the contents of the 5v9885 registers to the EEPROM.
PROGRESTORE is for loading the entire EEPROM contents to the 5v9885 registers.
EEPROM INTERFACE
EEPROM by issuing a save instruction (ProgSave) and can be loaded back to the internal programming registers by issuing a restore instruction (ProgRestore).
command code. The save or restore instruction executes after the STOP condition is issued by the Master, during which time the IDT5V9885 will not generate
Acknowledge bits. The 5V9885 will acknowledge the instructions after it has completed execution of them. During that time, the I
as busy by all other users of the bus.
During the execution of a ProgSave or ProgRestore instruction, the IDT5V9885 will not accept a new programming instruction (read, write, save, or restore).
All non-programming JTAG instructions will function properly, but the user should wait until the save or restore is complete before issuing a new programming
instruction. If a new programming instruction is issued before the save or restore completes, the new instruction is ignored, and the BYPASS register path remains
in effect for shifting data from TDI to TDO during data register scanning.
JTAG INTERFACE
CLAMP, HIGH-Z and BYPASS, the 5V9885 allows access to internal
programming registers using the REGADDR (set register address), REGDATAR
(read register) and REGDATW (write register instructions. Data is always
accessed by byte, and the register address increments after each read or write.
The full instruction set follows. The IDT5V9885 will be updating the registers
during programming.
PROGSAVE
PROGRESTORE
IDT5V9885
3.3V EEPROM PROGRAMMABLE CLOCK GENERATOR
S
S
The IDT5V9885 can also store its configuration in an internal EEPROM. The contents of the device's internal programming registers can be saved to the
To initiate a save or restore using I
Using JTAG, the ProgSave and ProgRestore instructions selects the BYPASS register path for shifting the data from TDI to TDO during the data register scanning.
The time it takes for the save (T
T
In addition to the IEEE 1149.1 instructions EXTEST, SAMPLE/PRELOAD,
The JTAG TAP controller can be reset in one of four ways:
1) Power up in JTAG mode
2) Power up in I
3) Apply TRST while in JTAG mode
4) Apply five rising edges of TCK with TMS high while in JTAG mode
SAVE
into JTAG mode with the I
Address
Address
7-bits
7-bits
= 100ms max, T
2
C mode and then go into JTAG mode, or go out of and back
R/W
R/W
0
0
RESTORE
ACK Command Code ACK
1-bit
ACK Command Code ACK
1-bit
2
C/JTAG pin
SAVE
= 10 ms max
2
C, only two bytes are transferred. The Device Address is issued with the read/write bit set to "0", followed by the appropriate
) and restore (T
8-bits:xxxxxx01
8-bits:xxxxxx10
RESTORE
) instructions to complete is:
1-bit
1-bit
P
P
24
JTAG INSTRUCTION REGISTER
DESCRIPTION
NOTES:
1. IEEE 1149.1 definition
2. REGADDR is for setting a specific 5v9885 register address.
3. REGDATAW/PROGWRITE is for writing to the 5v9885 registers.
4. REGDATAR/PROGREAD is for reading the 5v9885 registers.
5. PROGSAVE is for saving all the contents of the 5v9885 registers to the EEPROM.
6. PROGRESTORE is for loading the entire EEPROM contents to the 5v9885 registers.
7. The OEMs bits for OUT1-6 must be set for tri-state when using the HIGHZ instruction
IR (3)
0
0
0
0
0
0
0
0
1
1
1
IR (2)
0
0
0
0
1
1
1
1
0
0
1
IR (1)
0
0
1
1
0
0
1
1
0
0
1
IR (0)
INDUSTRIAL TEMPERATURE RANGE
0
1
0
1
0
1
0
1
0
1
1
EXTEST
SAMPLE/PRELOAD
IDCODE
REGADDR
REGDATAW / PROGWRITE
REGDATAR / PROGREAD
PROGSAVE
PROGRESTORE
CLAMP
HIGHZ
BYPASS
2
C bus should be interpreted
Instructions
(1,7)
(1)
(1)
(1)
(1)
(2)
(5)
(6)
(1)
(4)
(3)

Related parts for IDT5V9885NLGI8