1-6605310-1 TE Connectivity, 1-6605310-1 Datasheet - Page 4

• Manufacturer Part Number: 1-6605310-1
• Description: 1X1 MAG45 4DN2, 315 VOIP G/G R
• Manufacturer: TE Connectivity
• Series: Mag45r

Specifications of 1-6605310-1

• Product: Telecom & Ethernet Connectors
• Usoc Codes: RJ45
• Mounting Style: Through Hole
• Number Of Ports: 1
• Gender: Female
• Shielding: Shielded
• Contact Plating: Gold over Nickel
• Housing Material: Thermoplastic Polyethylene Terephthalate Polyester
• Contact Material: Phosphor Bronze
• Flammability Rating: UL 94 V-0
• Mounting Angle: Right Angle
• Number Of Rows: 1
• Operating Temperature Range: 0 C to + 70 C
• Termination Style: Solder
• Product Type: Connector
• Number Of Cores: 6
• Magnetics: Integrated Magnetics
• Jack Type: RJ45
• Power Over Ethernet (poe) Type: Enabled Power
• Signal Routing Type: Auto MDI/MDIX
• Profile: Standard
• Pcb Mounting Orientation: Side Entry (Right Angle)
• Jack Configuration: 1 x 1
• Turns Ratio: 1:1
• Shielded: Yes
• Emi Finger - Bottom: Without
• Termination Method: Solder
• Port Configuration: Single
• Emi Fingers -top And Sides: With
• Latch Orientation: Standard - Latch Down
• Pcb Tail Length (mm [in]): 3.68 [0.145]
• Contact Termination Type: Through Hole
• Preloaded: Yes
• Connector Style: Jack
• Status Indicator: LED
• Decoupling Capacitor: Without
• Rear Pcb Ground Tab: Without
• Signal Lead Quantity: 8
• Rohs/elv Compliance: Not ELV/RoHS compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Left Led Color (position #1): Green - 250 ohm resistor
• Right Led Color (position #2): Green - 250 ohm resistor
• Operating Temperature (°c [°f]): 0 – 70 [32 – 158]
• Applies To: Printed Circuit Board
• Environmental Conditions: Office / Premises
• Application: 10/100 POE
• Lead Free Status / Rohs Status: Details

Humidity, non-operational
Salt spray.
3.7.
Rev D
NOTE
Examination of product
Dry circuit resistance
Open circuit inductance
Random vibration, operational
Random vibration, non-operational
Durability, 500 cycles
Durability, 2000 cycles
Mating force
Unmating force
Normal force
Modular plug retention to modular jack
Thermal shock
Humidity-temperature cycling
Mixed flowing gas
Extended temperature
Humidity, non-operational
Salt spray
Product Qualification and Requalification Test Sequence
NOTE
Test Description
Shall meet visual requirements, show no physical damage, and meet requirements of additional
tests as specified in the Product Qualification and Requalification Test Sequence shown in
Figure 2.
Test or Examination
(a)
(b)
(c)
(d)
See paragraph 4.1.A.
Numbers indicate sequence in which tests are performed.
Measure inductance initially and at 50, 100, 150, 200, 250, 300, 350,
400, 450, 500, 550, 600, 650, 700, 750, 800, 1000, 1200, 1400, 1600,
1800 and 2000 cycles.
10 days mated; 5 days unmated; 5 days mated.
See Note.
Figure 1 (end)
Requirement
Figure 2
2, 7, 9
1, 5
3, 6
1
4
8
Test Sequence (b)
2 (d)
1, 3
Test Group (a)
2
MIL-STD-810,
Method 507.3.
Subject mated and mounted
specimens to 10 cycles (10 days)
between 30 and 60° C at 95 ± 5%
RH.
EIA-364-26,
Test Condition B.
Subject specimens to 5% spray at
35° C for 48 hours.
3
2
1
3
4
Procedure
1, 5, 8, 10
2 (c)
4
6
7
4
3
9
108-2100
4 of 6