DS1077LZ-66+ Maxim Integrated Products, DS1077LZ-66+ Datasheet - Page 12
![IC ECONOSCILL 2WIRE 66MHZ 8SOIC](/photos/1/39/13902/8-soic_21-0042b_sml.jpg)
DS1077LZ-66+
Manufacturer Part Number
DS1077LZ-66+
Description
IC ECONOSCILL 2WIRE 66MHZ 8SOIC
Manufacturer
Maxim Integrated Products
Series
EconOscillator™r
Type
Oscillator, Fixed Frequency, Dualr
Datasheet
1.DS1077LZ-40.pdf
(21 pages)
Specifications of DS1077LZ-66+
Frequency
66MHz
Voltage - Supply
2.7 V ~ 3.6 V
Current - Supply
30mA
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Count
-
COMMAND SET
Data and control information is read from and written to the DS1077L in the format shown in Figure 3. To
write to the DS1077L, the master will issue the slave address of the DS1077L and the R/
0. After receiving an acknowledge, the bus master provides a command protocol. After receiving this
protocol, the DS1077L will issue an acknowledge, and then the master can send data to the DS1077L. If the
DS1077L is to be read, the master must send the command protocol as before, and then issue a repeat
START condition and then the control byte again, this time with the R/
the data from the DS1077L. The command set for the DS1077L is as follows:
Access DIV [01]
If R/
is to be written into the DIV register.
If R/
Access MUX [02]
If R/
is to be written into the MUX register.
If R/
Access BUS [0D]
If R/
is to be written into the BUS register.
If R/
Write E2 [3F]
If WC = 0, the EEPROM is automatically written to at the end of each command, this is a DEFAULT
condition. In this case the command WRITE E2 is not needed
If WC = 1, the EEPROM is written when the WRITE E2 command is issued. On receipt of the WRITE E2
command the contents of the BUS, DIV, and MUX registers are written into the EEPROM, thus locking in
the register settings.
EXCEPTION: The BUS, DIV, and MUX registers are always automatically written to EEPROM after a
APPLICATION INFORMATION
Power-Supply Decoupling
To achieve best results, decouple the power supply with 0.01µF and 0.1µF high-quality, ceramic, surface-
mount capacitors as close as possible to V
inductance, which improves performance, and ceramic capacitors tend to have adequate high-frequency
response for decoupling applications.
Current Consumption
The active supply current can be significantly reduced by disabling OUT0 when not required and setting its
prescaler to divide by 8. Likewise, bypassing OUT1’s divider (and using only the prescaler) also
significantly reduces the supply current.
W
W
W
W
W
W
= 0, this command writes to the BUS register. After issuing this command, the next data byte value
= 1, the next data byte read is the value stored in the DIV register.
= 1, the next data byte read is the value stored in the MUX register.
= 1, the next data byte read is the value stored in the BUS register.
= 0, this command writes to the MUX register. After issuing this command, the next data byte value
= 0, this command writes to the DIV register. After issuing this command, the next data byte value
write to the BUS register regardless of the value of the WC bit.
CC
/GND of the device. Surface-mount components minimize lead
12 of 21
W
bit set to one to allow reading of
W
bit will be set to