MAX038CWP Maxim Integrated Products, MAX038CWP Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX038CWP
Manufacturer Part Number
MAX038CWP
Description
IC GEN WAVEFORM HI-FREQ 20-SOIC
Manufacturer
Maxim Integrated Products
Type
Waveform Generatorr
Datasheet
1.MAX038CPP.pdf
(16 pages)
Specifications of MAX038CWP
Frequency
20MHz
Voltage - Supply
4.75 V ~ 5.25 V
Current - Supply
45mA
Operating Temperature
0°C ~ 70°C
Package / Case
20-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Count
-
Other names
Q1136045
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX038CWP
Manufacturer:
HAMAMATSU
Quantity:
100
Part Number:
MAX038CWP
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX038CWP+
Manufacturer:
MAXIM/美信
Quantity:
20 000
DADJ is similar to FADJ; it has a 250µA constant cur-
rent sink to V- that must be furnished by the voltage
source. The source is usually an op-amp output, and
the temperature coefficient of the current sink becomes
unimportant. For manual adjustment of the duty cycle, a
variable resistor can be used to set V
250µA current sink’s temperature coefficient becomes
significant. Since external resistors cannot match the
internal temperature-coefficient curve, using external
resistors to program V
operation, when the operator can correct for any errors.
This restriction does not apply when V
voltage source.
A variable resistor, RD, connected between REF
(+2.5V) and DADJ provides a convenient means of
manually setting the duty cycle. The resistance value
(R
Note that both V
observe correct algebraic convention. For example, if
V
Varying the duty cycle in the range 15% to 85% has
minimal effect on the output frequency—typically less
than 2% when 25µA < I
wideband, and can be modulated at up to 2MHz (see
photos, Typical Operating Characteristics ).
The output amplitude is fixed at 2V
around ground, for all output waveforms. OUT has an
output resistance of under 0.1Ω, and can drive ±20mA
with up to a 50pF load. Isolate higher output capaci-
tance from OUT with a resistor (typically 50Ω) or buffer
amplifier.
REF is a stable 2.50V bandgap voltage reference capa-
ble of sourcing 4mA or sinking 100µA. It is principally
used to furnish a stable current to IIN or to bias DADJ
and FADJ. It can also be used for other applications
external to the MAX038. Bypass REF with 100nF to min-
imize noise.
The MAX038 produces a stable output frequency over
time and temperature, but the capacitor and resistors
that determine frequency can degrade performance if
they are not carefully chosen. Resistors should be
metal film, 1% or better. Capacitors should be chosen
High-Frequency Waveform Generator
12
DADJ
D
) is:
______________________________________________________________________________________
R
R
D
D
is -1.5V (23% duty cycle), the formula becomes:
= (V
= (+2.5V - (-1.5V)) ÷ 250µA
= (4.0V) ÷ 250µA = 16kΩ
Selecting Resistors and Capacitors
REF
- V
REF
DADJ
and V
DADJ
IN
) ÷ 250µA
< 250µA. The DADJ circuit is
DADJ
is intended only for manual
Reference Voltage
are signed values, so
Programming DADJ
DADJ
P-P
[15]
DADJ
, symmetrical
, but then the
Output
is a true
for low temperature coefficient over the whole tempera-
ture range. NPO ceramics are usually satisfactory.
The voltage on COSC is a triangle wave that varies
between 0V and -1V. Polarized capacitors are generally
not recommended (because of their outrageous tem-
perature dependence and leakage currents), but if they
are used, the negative terminal should be connected to
COSC and the positive terminal to GND. Large-value
capacitors, necessary for very low frequencies, should
be chosen with care, since potentially large leakage
currents and high dielectric absorption can interfere
with the orderly charge and discharge of C
ble, for a given frequency, use lower IIN currents to
reduce the size of the capacitor.
SYNC is a TTL/CMOS-compatible output that can be
used to synchronize external circuits. The SYNC output
is a square wave whose rising edge coincides with the
output rising sine or triangle wave as it crosses through
0V. When the square wave is selected, the rising edge
of SYNC occurs in the middle of the positive half of the
output square wave, effectively 90° ahead of the out-
put. The SYNC duty cycle is fixed at 50% and is inde-
pen-dent of the DADJ control.
Because SYNC is a very-high-speed TTL output, the
high-speed transient currents in DGND and DV+ can
radiate energy into the output circuit, causing a narrow
spike in the output waveform. (This spike is difficult to
see with oscilloscopes having less than 100MHz band-
width). The inductance and capacitance of IC sockets
tend to amplify this effect, so sockets are not recom-
mended when SYNC is on. SYNC is powered from sep-
arate ground and supply pins (DGND and DV+), and it
can be turned off by making DV+ open circuit. If syn-
chronization of external circuits is not used, turning off
SYNC by DV+ opening eliminates the spike.
The MAX038 contains a TTL/CMOS phase detector that
can be used in a phase-locked loop (PLL) to synchro-
nize its output to an external signal (Figure 3). The
external source is connected to the phase-detector
input (PDI) and the phase-detector output is taken from
PDO. PDO is the output of an exclusive-OR gate, and
produces a rectangular current waveform at the
MAX038 output frequency, even with PDI grounded.
PDO is normally connected to FADJ and a resistor,
R
of the phase detector, while the capacitor attenuates
high-frequency components and forms a pole in the
phase-locked loop filter.
PD
, and a capacitor CPD, to GND. R
Internal Phase Detector
Phase Detectors
SYNC Output
PD
sets the gain
F
. If possi-