DS1392U-33+ Maxim Integrated Products, DS1392U-33+ Datasheet - Page 17
![IC RTC W/CHARGER 10-USOP](/photos/6/57/65724/175-10-umax_sml.jpg)
DS1392U-33+
Manufacturer Part Number
DS1392U-33+
Description
IC RTC W/CHARGER 10-USOP
Manufacturer
Maxim Integrated Products
Type
Clock/Calendar/Trickle-Chargerr
Datasheet
1.DS1390U-33.pdf
(26 pages)
Specifications of DS1392U-33+
Time Format
HH:MM:SS:hh (12/24 hr)
Date Format
YY-MM-DD-dd
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.97 V ~ 3.63 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Function
Clock/Calendar/Alarm/Trickle Charger
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.97 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Rtc Bus Interface
Serial (3-Wire)
Supply Current
2 mA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Bit 7: Enable Oscillator (EOSC). When set to logic 0,
this bit starts the oscillator. When this bit is set to logic
1, the oscillator is stopped whenever the device is pow-
ered by V
when V
V
Bit 5: Battery-Backed Square-Wave and Interrupt
Enable (BBSQI). This bit when set to logic 1 enables the
square wave or interrupt output when V
the DS1390/DS1392/DS1393/DS1394 are being pow-
ered by the V
SQW/INT pin (or SQW and INT pins) goes high imped-
ance when V
bit is disabled (logic 0) when power is first applied.
Bits 4 and 3: Rate Select (RS2 and RS1). These bits
control the frequency of the square-wave output when
the square wave has been enabled. The table below
shows the square-wave frequencies that can be select-
ed with the RS bits. These bits are both set to logic 1
(32kHz) when power is first applied.
The DS1390–DS1394 have three additional registers
(control, status, and trickle charger) that control the
RTC, alarms, square-wave output, and trickle charger.
Control bits used in the DS1390 become general-pur-
pose, battery-backed, nonvolatile SRAM bits in the
DS1391.
RS2
CC
0
0
1
1
EOSC
BIT 7
EOSC
is first applied.
BIT 7
CC
RS1
0
1
0
1
BACKUP
is valid. This bit is enabled (logic 0) when
Special-Purpose Registers
CC
BACKUP
SQUARE-WAVE OUTPUT FREQUENCY
falls below the power-fail trip point. This
BIT 6
. The oscillator is always enabled
BIT 6
0
0
pin. When BBSQI is logic 0, the
32.768kHz
4.096kHz
8.192kHz
1Hz
BIT 5
Low-Voltage SPI/3-Wire RTCs with
BBSQI
BIT 5
X
____________________________________________________________________
CC
is absent and
BIT 4
BIT 4
RS2
X
Control Register (0D/8Dh) (DS1390/DS1393/DS1394 Only)
Bit 2: Interrupt Control (INTCN). This bit controls the
SQW/INT signal. When the INTCN bit is set to logic 0, a
square wave is output on the SQW/INT pin. The oscilla-
tor must also be enabled for the square wave to be out-
put. When the INTCN bit is set to logic 1, a match
between the timekeeping registers and either of the
alarm registers then activates the SQW/INT (provided
the alarm is also enabled). The corresponding alarm
flag is always set, regardless of the state of the INTCN
bit. The INTCN bit is set to logic 0 when power is first
applied.
Bit 0: Alarm Interrupt Enable (AIE). When set to logic
1, this bit permits the alarm flag (AF) bit in the status
register to assert SQW/INT (when INTCN = 1). When
the AIE bit is set to logic 0 or INTCN is set to logic 0,
the AF bit does not initiate the SQW/INT signal. The AIE
bit is disabled (logic 0) when power is first applied.
BIT 3
BIT 3
RS1
X
Control Register (0D/8Dh) (DS1391 Only)
BIT 2
INTCN
BIT 2
Trickle Charger
X
BIT 1
BIT 1
0
0
BIT 0
BIT 0
AIE
X
17