MAX5864ETM+ Maxim Integrated Products, MAX5864ETM+ Datasheet - Page 22
![IC ANLG FRONT END 22MSPS 48-TQFN](/photos/6/50/65028/48-qfn_21-0141_sml.jpg)
MAX5864ETM+
Manufacturer Part Number
MAX5864ETM+
Description
IC ANLG FRONT END 22MSPS 48-TQFN
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX5864ETM.pdf
(26 pages)
Specifications of MAX5864ETM+
Number Of Bits
10
Number Of Channels
4
Power (watts)
2.10W
Voltage - Supply, Analog
2.7 V ~ 3.3 V
Voltage - Supply, Digital
1.8 V ~ 3.3 V
Package / Case
48-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Ultra-Low-Power, High Dynamic-
Performance, 22Msps Analog Front End
Figure 11
MAX2391 and MAX2395 in TDD mode to provide a
complete radio front-end solution. Because the
MAX5864 DAC has full differential analog outputs with
a common-mode level of 1.4V, it can interface directly
with RF quadrature modulators while eliminating dis-
crete components and amplifiers used for level-shifting
circuits. Also, the DAC’s full dynamic range is pre-
served because the internally generated common-
mode level eliminates code-generated level shifting or
attenuation due to resistor level shifting. The MAX5864
ADC has 1V
mon-mode levels of V
simplify the analog interface between RF quadrature
demodulator and ADC while eliminating discrete gain
amplifiers and level-shifting components.
The MAX5864 requires high-speed board layout design
techniques. Refer to the MAX5865 EV kit data sheet for
a board layout reference. Locate all bypass capacitors
as close to the device as possible, preferably on the
same side of the board as the device, using surface-
mount devices for minimum inductance. Bypass V
GND with a 0.1µF ceramic capacitor in parallel with a
2.2µF capacitor. Bypass OV
Figure 12a. Integral Nonlinearity
22
___________________________________________________________________________________________________
illustrates the MAX5864 working with the
P-P
Grounding, Bypassing, and
7
6
5
4
3
2
1
0
000
full-scale range and accepts input com-
001
DD
010
DIGITAL INPUT CODE
AT STEP
001 (1/4 LSB )
/2 (±200mV). These features
011
DD
100
AT STEP
011 (1/2 LSB )
to OGND with a 0.1µF
Board Layout
101
110
111
DD
to
ceramic capacitor in parallel with a 2.2µF capacitor.
Bypass REFP, REFN, and COM each to GND with a
0.33µF ceramic capacitor. Bypass REFIN to GND with
a 0.1µF capacitor.
Multilayer boards with separated ground and power
planes yield the highest level of signal integrity. Use a
split ground plane arranged to match the physical loca-
tion of the analog ground (GND) and the digital output
driver ground (OGND) on the device package. Connect
the MAX5864 exposed backside paddle to the GND
plane. Join the two ground planes at a single point
such that the noisy digital ground currents do not inter-
fere with the analog ground plane. The ideal location
for this connection can be determined experimentally at
a point along the gap between the two ground planes.
Make this connection with a low-value, surface-mount
resistor (1Ω to 5Ω), a ferrite bead, or a direct short.
Alternatively, all ground pins could share the same
ground plane, if the ground plane is sufficiently isolated
from any noisy digital system’s ground plane (e.g.,
downstream output buffer or DSP ground plane).
Route high-speed digital signal traces away from sensi-
tive analog traces. Make sure to isolate the analog
input lines to each respective converter to minimize
channel-to-channel crosstalk. Keep all signal lines short
and free of 90° turns.
Figure 12b. Differential Nonlinearity
6
5
4
3
2
1
0
000
001
DIGITAL INPUT CODE
010
1 LSB
011
DIFFERENTIAL
LINEARITY ERROR (+1/4 LSB)
DIFFERENTIAL LINEARITY
ERROR (-1/4 LSB)
100
101
1 LSB