AD7714ANZ-5 Analog Devices Inc, AD7714ANZ-5 Datasheet - Page 33

• Manufacturer Part Number: AD7714ANZ-5
• Description: IC ADC SIGNAL COND 5V 24-DIP
• Manufacturer: Analog Devices Inc

Specifications of AD7714ANZ-5

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 24
• Sampling Rate (per Second): 1k
• Number Of Converters: 1
• Power Dissipation (max): 7mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 24-DIP (0.300", 7.62mm)
• Resolution (bits): 24bit
• Sampling Rate: 1kSPS
• Input Channel Type: Differential
• Supply Voltage Range - Analog: 4.75V To 5.25V
• Supply Current: 1.1mA
• Digital Ic Case Style: DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7714-3EBZ - BOARD EVALUATION FOR AD7714
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

/* This program has read and write routines for the 68HC11 to interface to the AD7714 and the sample
program sets the various registers and then reads 1000 samples from the part. */
#include <math.h>
#include <io6811.h>
#define NUM_SAMPLES 1000 /* change the number of data samples */
#define MAX_REG_LENGTH 3 /* this says that the max length of a register is 3 bytes */
Writetoreg (int);
Read (int,char);
char *datapointer = store;
char store[NUM_SAMPLES*MAX_REG_LENGTH + 30];
void main()
{
of PORTC is made as an output */
char a;
DDRC = 0x04; /* PC2 is an output the rest of the port bits are inputs */
PORTC | = 0x04;
Writetoreg(0x27); /* set the channel AIN6/AIN6 and set the next operation as write to the filter high
register */
Writetoreg(0x4f); /* set Bipolar mode, 24 bits, boost off, all 4 MSBs of filterword to 1 */
Writetoreg(0x37); /* set the next operation as a write to the filter low register */
Writetoreg(0xA0); /* max filter word allowed for low part of the filterword */
Writetoreg(0x17); /* set the operation as a write to the mode register */
Writetoreg(0x20); /* set gain to 1, burnout current off, no filter sync, and do a self calibration */
while(PORTC & 0x10); /* wait for /DRDY to go low */
for(a=0;a<NUM_SAMPLES;a++);
}
Writetoreg(int byteword);
{
int q;
SPCR = 0x3f;
SPCR = 0X7f; /* this sets the WiredOR mode(DWOM=1), Master mode(MSTR=1), SCK idles high(CPOL=1), /SS
can be low always (CPHA=1), lowest clock speed(slowest speed which is master clock /32 */
DDRD = 0x18; /* SCK, MOSI outputs */
q = SPSR;
q = SPDR;
which tells the user that the data transfer is complete */
PORTC &= 0xfb; /* /CS is low */
SPDR = byteword;
while(!(SPSR & 0x80));
PORTC |= 0x4;
}
Read(int amount, int reglength)
{
int q;
SPCR = 0x3f;
SPCR = 0x7f;
DDRD = 0x10;
while(PORTC & 0x10);
PORTC & 0xfb ; /* /CS is low */
for(b=0;b<reglength;b++)
PORTC|=4; /* /CS is high */
}
REV. C
/* the only pin that is programmed here from the 68HC11 is the /CS and this is why the PC2 bit
{
Writetoreg(0x5f); /*set the next operation for 24 bit read from the data register */
Read(NUM_SAMPES,3);
}
{
SPDR = 0;
while(!(SPSR & 0x80));
*datapointer++=SPDR;
}
/* the read of the staus register and of the data register is needed to clear the interrupt
/* clear the interupt */
/* MOSI output, MISO input, SCK output */
/* /CS high */
/* make the /CS line high */
/* put the byte into data register */
/* wait for /DRDY to go low */
/* wait for /DRDY to go low */
/* read SPDR into store array via datapointer */
Table XV. C Code for Interfacing AD7714 to 68HC11
/* wait until port ready before reading */
–33–
AD7714
2