TC7109ACPL Microchip Technology, TC7109ACPL Datasheet - Page 20

• Manufacturer Part Number: TC7109ACPL
• Description: IC ADC 12BIT HANDSHAKE 40DIP
• Manufacturer: Microchip Technology

Specifications of TC7109ACPL

• Number Of Bits: 12
• Data Interface: Serial, Parallel
• Number Of Converters: 1
• Voltage Supply Source: Dual ±
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 158-1130; 158-1130

TC7109/A
4.2
The Handshake mode provides an interface to a wide
variety of external devices. The byte enables may be
used as byte identification flags, or as load enables,
and external latches may be clocked by the rising edge
of CE/LOAD. A handshake interface to Intel
cessors using an 8255 PPI is shown in Figure . The
handshake operation with the 8255 is controlled by
inverting its Input Buffer Full (IBF) flag to drive the
SEND input to the TC7109A, and using the CE/LOAD
to drive the 8255 strobe. The internal control register of
the PPI should be set in MODE 1 for the port used. If
the 8255 IBF flag is LOW and the TC7109A is in Hand-
shake mode, the next word will be strobed into the port.
The strobe will cause IBF to go HIGH (SEND goes
LOW), which will keep the enabled byte outputs active.
The PPI will generate an interrupt which, when
executed, will result in the data being read. The IBF will
be reset LOW when the byte is read, causing the
TC7109A to sequence into the next byte. The MODE
input to the TC7109A is connected to the control line on
the PPI.
The data from every conversion will be sequenced in
two bytes in the system, if this output is left HIGH, or
tied HIGH separately. (The data access must take less
time than a conversion.) The output sequence can be
obtained on demand if this output is made to go from
LOW to HIGH and the interrupt may be used to reset
the MODE bit.
FIGURE 4-6:
DS21456C-page 20
GND
GND
Serial
Output
+5V
+5V
Serial
Input
*Note:
5–12
13
14
15
16
20
25
Handshake Mode
1
3
4
For lowest power consumption, TBR1-TBR8 inputs should have 100kΩ pull-up resistors to +5V.
Send any word to UART to transmit latest result.
V
GND
RRD
RBR1–8
PE
FE
OE
SFD
RR1
TRO
CMOS UART
HD-640R
TC7109 Typical UART Interface
*TBR1–8
TBRE
TBRL
CLS1
CLS2
RRC
DRR
TRC
EPE
SBS
CRL
TRE
MR
DR
PI
40
17
39
38
37
36
35
34
26–33
24
18
19
23
22
21
15
GND
+5V
GND
Q3
RESET
+5V
CD4060B
11
®
micropro-
8
CLK
10
GND
6
8
9–16
3–8
25
19
17
18
21
20
27
1
2
GND
BUFF OSC OUT
STATUS
HBEN
B
TEST
LBEN
MODE
CE/LOAD
SEND
B
POL, OR
1
Conversions may be obtained on command under soft-
ware control by driving the RUN/HOLD input to the
TC7109A by a bit of the 8255. Another peripheral
device may be serviced by the unused port of the 8255.
The Handshake mode is particularly useful for directly
interfacing to industry standard UARTs (such as Intersil
HD-6402), providing a means of serially transmitting
converted data with minimum component count.
A typical UART connection is shown in Figure . In this
circuit, any word received by the UART causes the
UART DR (Data Ready) output to go HIGH. The MODE
input to the TC7109A goes HIGH, triggering the
TC7109A into Handshake mode. The high order byte is
output to the UART and when the UART has trans-
ferred the data to the Transmitter register, TBRE
(SEND) goes HIGH again, LBEN will go HIGH, driving
the UART DRR (Data Ready Reset), which will signal
the end of the transfer of data from the TC7109A to the
UART.
An extension of the typical connection to several
TC7109A’s with one UART is shown in Figure 4-7. In
this circuit, the word received by the UART (available at
the RBR outputs when DR is HIGH) is used to select
which converter will handshake with the UART. Up to
eight TC7109A’s may interface with one UART, with no
external components. Up to 256 converters may be
accessed
components.
9
- B
- B
8
TC7109A
12
,
RUN/HOLD
REF CAP+
on
REF CAP-
OSC OUT
REF OUT
OSC SEL
REF IN+
REF IN-
OSC IN
IN LO
BUFF
COM
IN HI
one
INT
AZ
V+
V-
40
39
38
37
36
35
34
33
32
31
30
29
28
26
24
23
22
serial
© 2006 Microchip Technology Inc.
-5V
+5V or Open
GND
C
0.33μF
+5V
R
AZ
INT
0.01μF
1μF
3.58MHz
Crystal
100kΩ
line
C
0.15μF
1MΩ
20kΩ
INT
with
External
Reference
0.2V
1V
–
+
+
–
Analog GND
REF
Input
REF
additional