MAX1143ACAP+ Maxim Integrated Products, MAX1143ACAP+ Datasheet - Page 10
![IC ADC 14BIT 200KSPS 20-SSOP](/photos/1/39/13938/175-20-ssop_sml.jpg)
MAX1143ACAP+
Manufacturer Part Number
MAX1143ACAP+
Description
IC ADC 14BIT 200KSPS 20-SSOP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1142BEAP.pdf
(20 pages)
Specifications of MAX1143ACAP+
Number Of Bits
14
Sampling Rate (per Second)
200k
Data Interface
MICROWIRE™, QSPI™, Serial, SPI™
Number Of Converters
1
Power Dissipation (max)
640mW
Voltage Supply Source
Analog and Digital
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
20-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
14-Bit ADC, 200ksps, +5V Single-Supply
with Reference
The MAX1142/MAX1143 have three user-programma-
ble outputs: P0, P1 and P2. The power-on default state
for the programmable outputs is zero. These are push-
pull CMOS outputs suitable for driving a multiplexer, a
PGA, or other signal preconditioning circuitry. The user-
programmable outputs are controlled by bits 0, 1 and 2
of the Control-Byte (Table 2).
The user-programmable outputs are set to zero during
power-on reset (POR) or when RST goes low. During
hardware or software shutdown P0, P1, and P2 are
unchanged and remain low-impedance.
Start a conversion by clocking a Control-Byte into the
device’s internal shift register. With CS low, each rising
edge on SCLK clocks a bit from DIN into the
MAX1142/MAX1143’s internal shift register. After CS
goes low or after a conversion or calibration completes,
the first arriving logic “1” is defined as the start bit of
the Control-Byte. Until this first start bit arrives, any
number of logic “0” bits can be clocked into DIN with
no effect. If at any time during acquisition or conversion,
CS is brought high and then low again, the part is
placed into a state where it can recognize a new start
Table 1. Control-Byte Format
10
7 (MSB)
START
0(LSB)
(MSB)
______________________________________________________________________________________
BIT7
BIT
6
5
4
3
2
1
INT/EXT
UNI/BIP
UNI/BIP
START
User-Programmable Outputs
NAME
BIT6
M1
M0
P2
P1
P0
Starting a Conversion
The first logic “1” bit, after CS goes low, defines the beginning of the Control-Byte
1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, analog
input signals from 0 to +12V (MAX1142) or 0 to V
mode analog input signals from -12V to +12V (MAX1142) or -V
converted.
Selects the internal or external conversion clock. 1 = Internal, 0 = External.
These three bits are stored in a port register and output to pins P2–P0 for use in addressing a
MUX or PGA. These three bits are updated in the port register simultaneously when a new
Control-Byte is written.
INT/EXT
BIT5
M1
0
0
1
1
BIT4
M1
M0
0
1
0
1
24 External clocks per conversion (short acquisition mode)
Start Calibration. Starts internal calibration
Software power-down mode
32 External clocks per conversion (long acquisition mode)
bit. If a new start bit occurs before the current conver-
sion is complete, the conversion is aborted and a new
acquisition is initiated. Table 1 shows the Control-Byte
format.
The MAX1142/MAX1143 may use either the external
serial clock or the internal clock to perform the succes-
sive-approximation conversion. In both clock modes,
the external clock shifts data in and out of the
MAX1142/MAX1143. Bit 5 (INT/EXT) of the Control-Byte
programs the clock mode.
In external clock mode, the external clock not only
shifts data in and out, but it also drives the A/D conver-
sion steps. In short acquisition mode, SSTRB pulses
high for one clock period after the seventh falling edge
of SCLK, following the start bit. The MSB of the conver-
sion is available at DOUT on the eighth falling edge of
SCLK (Figure 2).
In long acquisition mode, when using the external
clock, SSTRB pulses high for one clock period after the
fifteenth falling edge of SCLK, following the start bit.
The MSB of the conversion is available at DOUT on the
sixteenth falling edge of SCLK (Figure 3).
BIT3
M0
DESCRIPTION
Internal and External Clock Modes
REF
(MAX1143) can be converted. In bipolar
BIT2
P2
REF
MODE
to +V
BIT1
REF
P1
(MAX1143) can be
External Clock
(LSB)
BIT0
P0