4-647010-1 TE Connectivity, 4-647010-1 Datasheet - Page 6
![11P MTA100 PSTD CONN ASSY LF](/photos/41/47/414797/pr8205620a_sml.jpg)
4-647010-1
Manufacturer Part Number
4-647010-1
Description
11P MTA100 PSTD CONN ASSY LF
Manufacturer
TE Connectivity
Specifications of 4-647010-1
Connector Type
Connector Assembly
Connector Design
Closed End
Product Line
MTA-100
Termination Method To Wire/cable
IDC Standard
Wire Size (mm² [awg])
0.12-0.15² [26]
Mating Connector Lock
Without
Four Points Of Contact
Without
Shrouded
No
Mounting Ears
Without
Panel Mount Retention
Without
Voltage Rating (vac)
250
Solder Tail Contact Plating
Bright Tin
Number Of Positions
11
Centerline (mm [in])
2.54 [0.100]
Narrow
No
Post Number(s) Omitted
None
Contact Type
Socket
Contact Plating, Mating Area, Material
Gold (30) or (30) Total Gold Flash over Palladium Nickel
Contact Base Material
Copper Alloy
Connector Style
Receptacle
Housing Color
Blue
Mating Alignment
Without
Ul Flammability Rating
UL 94V-2
Housing Material
Nylon
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Applies To
Wire/Cable
Application Use
Wire-to-Wire
4.
4.1.
4.2.
4.3.
4.4.
Rev D
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 1. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. When
product failure occurs, corrective action shall be taken and samples resubmitted for qualification.
Testing to confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan will specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Sample Selection
Samples shall be prepared in accordance with applicable Instruction Sheets and shall be selected
at random from current production. All test groups shall each consist of mated pairs of MTA-100
posted connectors and standard connectors to form a wire-to-wire connector system unless
otherwise required by the test procedure. All test groups will also utilize strain relief dust covers
during testing to prevent wire removal from the IDC blade. Test group 1 shall consist of 5 mated,
16 position tin-lead plated samples terminated with 6 inch lengths of 22 AWG wire. Test group 2
shall consist of 3 mated, 16 position tin-lead plated samples terminated with 12 inch lengths of 22
AWG wire and 3, 16 position tin-lead plated samples terminated with 12 inch lengths of 28 AWG
wire. Test group 3 shall consist of 5 mated, 16 position gold plated samples terminated with 22
AWG wire. Test group 4 shall consist of 5 mated, 8 position tin-lead plated samples terminated
with 22 AWG wire. Test group 5 shall consist of 5 pieces each of 16 position tin-lead plated
samples in each wire gage.
Test Sequence
Qualification inspection shall be verified by testing samples as specified in Figure 2.
108-1050-1
6 of 11