4-647108-2 TE Connectivity, 4-647108-2 Datasheet - Page 5
![12P MTA100 HDR ASSY 30AU LF](/photos/41/48/414827/pr8205629a_sml.jpg)
4-647108-2
Manufacturer Part Number
4-647108-2
Description
12P MTA100 HDR ASSY 30AU LF
Manufacturer
TE Connectivity
Specifications of 4-647108-2
Connector Type
Header
Product Line
MTA-100
Pcb Mounting Orientation
Vertical
Pcb Mount Retention
Without
Mating Connector Lock
Without
Four Points Of Contact
Without
Shrouded
No
Mounting Ears
Without
Post Size (mm [in])
0.64 [.025]
Panel Mount Retention
Without
Surface Mountable
Yes
Voltage Rating (vac)
250
Solder Tail Contact Plating
Matte Tin
Termination Post Length (mm [in])
3.18 [0.125]
Number Of Positions
12
Centerline (mm [in])
2.54 [0.100]
Narrow
No
Post Number(s) Omitted
None
Solder Tail Contact Material
Copper Alloy
Contact Type
Pin
Contact Shape
Square
Contact Plating, Mating Area, Material
Gold (30) or (30) Total Gold Flash over Palladium Nickel
Contact Base Material
Copper Alloy
Connector Style
Plug
Housing Color
Black
Mating Alignment
With
Ul Flammability Rating
UL 94V-0
Housing Material
Nylon 4/6
Backwall/post Interruption(s)
Without
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Reflow solder capable to 245°C, Reflow solder capable to 260°C
Rohs/elv Compliance History
Always was RoHS compliant
Applies To
Printed Circuit Board
Application Use
Wire-to-Board
4.
4.1.
4.2.
4.3.
4.4.
Rev H
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets requirements of Figure 1. Failures attributed
to equipment, test setup or operator deficiencies shall not disqualify product. When product failure
occurs, corrective action shall be taken and samples resubmitted for qualification. Testing to confirm
corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan will specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Sample Selection
Samples shall be prepared in accordance with applicable Instruction Sheets and shall be selected
at random from current production. Test group 1 shall consist of 5, 6 position standard tin-lead
plated samples and 5, 6 position gold plated samples. All samples shall be terminated to the
maximum wire size and mounted on printed circuit board PN 93-660017 (see Figure 5). Test group
2 shall consist of 3, 10 position standard tin-lead plated samples terminated to 28 AWG wire and
mounted on printed circuit board PN 93-660652; and 3, 10 position standard tin-lead plated
samples terminated to 22 AWG wire and mounted on printed circuit board PN 93-660651 (see
Figure 5). Test group 3 shall consist of 3, 10 position gold plated samples terminated to 22 AWG
wire and mounted on printed circuit board PN 93-660017. Test group 4 shall consist of 5
unmounted 24 position standard tin-lead plated samples terminated to the maximum wire size.
Test group 5 shall consist of 6, 10 position standard tin-lead plated samples terminated to 28 AWG
wire; 6, 10 position standard tin-lead plated samples terminated to 24 AWG wire; and 6, 10
position standard tin-lead plated samples terminated to 22 AWG wire. All samples shall be
unmated and unmounted. Test group 6 shall consist of 5, 6 position .100 inch friction lock tin-lead
plated headers.
Test Sequence
Qualification inspection shall be verified by testing samples as specified in Figure 2.
108-1050
5 of 9