LTC2418CGN Linear Technology, LTC2418CGN Datasheet - Page 33

• Manufacturer Part Number: LTC2418CGN
• Description: IC ADC 24BIT DIFF INPUT 28SSOP
• Manufacturer: Linear Technology

Specifications of LTC2418CGN

• Number Of Bits: 24
• Sampling Rate (per Second): 7.5
• Data Interface: MICROWIRE™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 1mW
• Voltage Supply Source: Single Supply
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP (0.150", 3.95mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIO S I FOR ATIO
When external amplifiers are driving the LTC2414/
LTC2418, the ADC input referred system noise calculation
can be simplified by Figure 32. The noise of an amplifier
driving the LTC2414/LTC2418 input pin can be modeled
as a band limited white noise source. Its bandwidth can be
approximated by the bandwidth of a single pole lowpass
filter with a corner frequency f
tral density is n
selector, we can find on the y-axis the noise equivalent
bandwidth freq
width includes the band limiting effects of the ADC internal
calibration and filtering. The noise of the driving amplifier
referred to the converter input and including all these
effects can be calculated as N = n
noise (referred to the LTC2414/LTC2418 input) can now
be obtained by summing as square root of sum of squares
the three ADC input referred noise sources: the LTC2414/
LTC2418 internal noise (1µV), the noise of the IN
amplifier and the noise of the IN
If the F
f
x-axis is scaled by f
ratio f
decrease, but in the same time the LTC2414/LTC2418
noise floor rises and the noise contribution of the driving
amplifiers lose significance.
Normal Mode Rejection and Antialiasing
One of the advantages delta-sigma ADCs offer over con-
ventional ADCs is on-chip digital filtering. Combined with
a large oversampling ratio, the LTC2414/LTC2418 signifi-
cantly simplify antialiasing filter requirements.
The Sinc
mode rejection at all frequencies except DC and integer
multiples of the modulator sampling frequency (f
LTC2414/LTC2418’s autocalibration circuits further sim-
plify the antialiasing requirements by additional normal
mode signal filtering both in the analog and digital domain.
Independent of the operating mode, f
• f
the maximum output data rate. In the internal oscillator
mode with a 50Hz notch setting, f
60Hz notch setting f
mode, f
EOSC
OUTMAX
, Figure 32 can still be used for noise calculation if the
EOSC
O
S
pin is driven by an external oscillator of frequency
4
= f
digital filter provides greater than 120dB normal
where f
/153600, the Figure 32 plot accuracy begins to
EOSC
i
i
of the input driving amplifier. This band-
. From Figure 32, using f
/10.
N
in the notch frequency and f
U
S
EOSC
= 15360Hz. In the external oscillator
/153600. For large values of the
U
i
. The amplifier noise spec-
i
–
• √freq
S
driving amplifier.
W
= 12800Hz and with a
S
i
= 256 • f
. The total system
i
as the x-axis
U
OUTMAX
N
+
S
= 2048
driving
). The
is
Figure 32. Input Referred Noise Equivalent Bandwidth
of an Input Connected White Noise Source
Figure 34. Input Normal Mode Rejection, Internal
Oscillator and 60Hz Notch or External Oscillator
–100
–110
–120
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
Figure 33. Input Normal Mode Rejection,
Internal Oscillator and 50Hz Notch
0
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
–100
–110
–120
100
–10
–20
–30
–40
–50
–60
–70
–80
–90
0.1
10
f
S
1
0
0.1
0 f
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2f
S
S
INPUT NOISE SOURCE SINGLE POLE
F
3f
1
O
2f
LTC2414/LTC2418
S
EQUIVALENT BANDWIDTH (Hz)
= HIGH
S
4f
3f
S
10
S
4f
5f
S
S
100
5f
6f
F
F
S
O
O
S
6f
= LOW
= HIGH
7f
S
1k
S
7f
S
8f
8f
S
10k 100k
S
2414/18 F34
9f
9f
S
S
10f
10f
2414/18 F33
S
S
2414/18 F32
11f
F
F
f
EOSC
O
O
S
= LOW OR
= EXTERNAL
1M
12f
OSCILLATOR,
= 10 • f
S
33
S
241418fa