AD7927BRUZ Analog Devices Inc, AD7927BRUZ Datasheet - Page 25

• Manufacturer Part Number: AD7927BRUZ
• Description: IC ADC 12BIT 8CH 200KSPS 20TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7927BRUZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 12
• Sampling Rate (per Second): 200k
• Number Of Converters: 1
• Power Dissipation (max): 7.5mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP (0.173", 4.40mm Width)
• Resolution (bits): 12bit
• Sampling Rate: 200kSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Analog: 2.7V To 5.25V
• Supply Current: 1.5mA
• Number Of Elements: 1
• Resolution: 12Bit
• Architecture: SAR
• Sample Rate: 200KSPS
• Input Polarity: Unipolar
• Input Type: Voltage
• Rated Input Volt: 2.5/5V
• Differential Input: No
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 3/5V
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 7.5mW
• Differential Linearity Error: -0.9LSB/1.5LSB
• Integral Nonlinearity Error: ±1LSB
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: TSSOP
• Input Signal Type: Single-Ended
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7927CBZ - BOARD EVALUATION FOR AD7927
• Lead Free Status / Rohs Status: Compliant

For example, if the ADSP-2189 had a 20 MHz crystal such that
it had a master clock frequency of 40 MHz, then the master
cycle time would be 25 ns. If the SCLKDIV register is loaded
with the value of 3, then an SCLK of 5 MHz is obtained and
eight master clock periods elapse for every one SCLK period.
Depending on the throughput rate selected, if the timer registers
are loaded with the value, of 803, for example, then 100.5 SCLKs
occur between interrupts and subsequently between transmit
instructions. This situation results in sampling that is not equi-
distant as the transmit instruction is occurring on a SCLK edge.
If the number of SCLKs between interrupts is a whole integer
figure of N, then equidistant sampling is implemented by the DSP.
AD7927 TO DSP563xx
The connection diagram in Figure 31 shows how the AD7927
can be connected to the enhanced synchronous serial interface
(ESSI) of the DSP563xx family of DSPs from Motorola. Each
ESSI (two on board) is operated in synchronous mode (SYN
bit in CRB = 1) with internally generated word length frame
sync for both TX and RX (Bit FSL1 = 0 and Bit FSL0 = 0 in
CRB). Normal operation of the ESSI is selected by making
MOD = 0 in the CRB. Set the word length to 16 by setting bits
Rev. A | Page 25 of 28
WL1 = 1 and WL0 = 0 in CRA. The FSP bit in the CRB should
be set to 1 so the frame sync is negative. It should be noted that
for signal processing applications, it is imperative that the frame
synchronization signal from the DSP563xx provides equidistant
sampling.
In the example shown in Figure 31, the serial clock is taken
from the ESSI so the SCK0 pin must be set as an output, SCKD
= 1. The V
as that of the DSP563xx. This allows the ADC to operate at a
higher voltage than the serial interface, that is, DSP563xx, if
necessary.
*ADDITIONAL PINS REMOVED FOR CLARITY.
AD7927
V
DRIVE
DRIVE
DOUT
SCLK
*
DIN
CS
pin of the AD7927 takes the same supply voltage
Figure 31. Interfacing to the DSP563xx
SCK
SRD
STD
SC2
DSP563xx*
V
AD7927
DD